1. Gold rush era (1896~1899)

2. Methods of bringing out the gold
    Underground mining  Hydraulic methods and mining in benches  Separation methods 

3. Later operations (1910-1950)

4. References

Gold rush era (1896~1899)

During the gold rush some gold was found in the creek beds, but most was in the valley gravels near and in bedrock. The recovery had two steps: bringing the gravel containing gold to the surface and then separating the gold from the gravel using water and gravity separation, as a result access to water was important since it was necessary for the separation process and could also be used thawing the permanently frozen ground and washing down gravels from the upper terraces.

Methods of bringing out the gold

The first step of recovery was to bring the mixture of gold and dirt from the ground to the surface or from a hillside down to a bench. There were two methods: digging a shaft or using water under pressure to either wash down a hillside or suck up earth from the ground.

Underground mining

Most of the gold was below the surface. The miners first had to thaw the permafrost before they could dig.^[2] A fire burning all night was used to soften the ground. This would then thaw to a depth of about 14 inches and the gravel could be removed. The process was repeated until the gold was reached. No support of the shaft was necessary because of the permafrost. However, the fire could produce noxious gas which had to be removed.^[3] Over time steam for thawing the ground were also taken into use.^[2] Normally digging was done during the winter. The cold air would sink down into the shaft and renew the air automatically. At the same time the temperature meant that shafts, apart from not needing support, were not at risk of being filled with water. A dump was made that could be sluiced during the summer. In the dump, the gold was protected from theft because it was invisible in frozen gravel.^[4]

Hydraulic methods and mining in benches

Jets were applied to wash down part of a hillside for sluicing.^[5] The stream could be so strong that it would reflect a crowbar swung at it.^[6] When gravity could not be used for sluicing, a lift could be applied; it used pressurized water, introduced at the bottom, to suck up a mixture of water and gravel.^[7] This could also be an alternative to shaft mining as seen on picture 2. Hydraulic methods were introduced during the California gold rush and would be used later at Nome.

Separation methods

All methods required water and because of that they could only be used during the summer. Panning for gold was the simplest method of recovering gold, but mostly used for prospecting since it was slow. A faster way was by a rocker box or by sluicing. Dirt was filled into the box or sluice together with water and rocking movements or gravity would make the gold particle go to the bottom whereas sand and fine gold particles would flow off with the water. Further purification of the gold could be done with mercury that would amalgamate with gold only and leave fine sand particles out. A magnet could be used to separate fine magnetic sand from gold dust.{{citation needed|date=December 2011}}

Later operations (1910-1950)

Today a mixture of hydraulic methods together with bulldozers are used.^[11]

References

• Clothing retail
• Clothing retailer
• Clothing retailing
• Clothing sector
• Cloth of gold cone
• Cloth of Stars
• Clotho Tessera
• Cloth Sack Monk
• Cloth. & Textiles Res. J.
• Cloth & Textiles Res J
• Cloth. Text. Res. J.
• Cloth Text Res J
• CLOTH vowel
• Cloth-Workers' Company
• Cloth wrapper
• Cloticasone
• Clotidiella
• Clotilda (disambiguation)
• Clotilde Apponyi
• Clotilde Armand
• Clotilde Betances Jaeger
• Clotilde Bressler-Gianoli
• Clotilde-Camille DeFlandre
• Clotilde-Camille Deflandre
• Clotilde Colon