| 词条 | Harman geared locomotive |
| 释义 |
| name = Harman geared locomotive | image = Harman geared locomotive built for the State Forestry Commission of Victoria in 1927.jpg | alt = | caption = Harman geared locomotive built for the State Forestry Commission of Victoria in 1927 | powertype = Steam | designer = Alfred Harman from Melbourne | builder = Alfred Harman from Melbourne | ordernumber = | serialnumber = | buildmodel = | builddate = | totalproduction = | rebuilder = | rebuilddate = | numberrebuilt = | whytetype = | uicclass = | driver = | gauge = 2ft 6in gauge | leadingdiameter = | driverdiameter = 28.5" | coupleddiameter = | trailingdiameter = | tenderdiameter = | minimumcurve = | wheelbase = Two four-wheel bogies, which were constructed with heavy side-plates, carrying the horn cheeks, steel axleboxes, end plates and a central steel casting, which supported the ball bearings of the transverse shafts of the reduction gear.[1] | engine total = | leading = | drivers = | coupled = | trailing = | tender total = | tendertruck = | tenderbogie = | pivotcentres = | wheelspacing = | length = | over couplers = 26' | over bufferbeams= | width = 5' 4" | height = 10' | frametype = Rolled steel joists (12" x 6" x 54 lbs.), boiler rigidly attached at the firebox and supported on a cradle at the smokebox end.[1] | axleload = | leadingbogie/pony= | coupled all = | coupled 1 = | coupled 2 = | coupled 3 = | coupled 4 = | coupled 5 = | coupled 6 = | coupled 7 = | coupled 8 = | trail bogie/pony= | tenderbogieload = | tenderaxle = | weightondrivers = | locoweight = Specified: 16 to 18 tons. Actual: 26 tons | tenderweight = | locotenderweight = | tendertype = | fueltype = | fuelcap = | watercap = 270 gallons centred under the main frame | tendercap = 200 gallons in the tender | sandcap = | fireboxtype = | firearea = | boiler = Messrs. Johnson & Son | boilertype = | pitch = | diameterinside = 2' 10" | lengthinside = 6' 6" | smalltubediameter= | largetubediameter= | boilerpressure = 200 lbs. per square inch | safetyvalvetype = | feedwaterheater = | totalsurface = 257.7 sq. ft. | tubearea = 212.5 sq. ft | archarea = | fluearea = | tubesandflues = | fireboxarea = (4'3" x 2' 5" x 3') 45.2 sq. ft. | superheatertype = | superheaterarea = | cylindercount = Each bogie was equipped with two cylinders, which operated crankshafts, running in ball bearings. The big ends were also fitted with ball bearings.[1] | cylindersize = 6" x 6" | frontcylindersize= | rearcylindersize = | hpcylindersize = | lpcylindersize = | valvegear = | valvetype = | valvetravel = | valvelap = | valvelead = | transmission = A steel spur gear on the transverse shaft provided the first reduction, the second being through the following chain and sprocket drive to the axles, the total providing a 4to1 ratio.[1] | trainheating = | locobrakes = | locobrakeforce = | trainbrakes = | safety = A Cheney spark nullifier, by Cheney of Bayswater, Western Australia, was fitted to the stack to minimise the fire risk. The usual smokebox conditions did not exist, as exhaust steam, instead of entering a blast-pipe, was taken to the top of the smokestack and expelled through a slotted ring, to form a cone of saturated steam. This was an added fire prevention measure, as all products of combustion passed through this steam. The draught required was provided by the turbine furnace, with which the locomotive was fitted, an arrangement that brought the rate of combustion directly under the driver's control.[1] | coupling = | maxspeed = | poweroutput = | tractiveeffort = 9374 lbs., less 10% due to gear losses, giving 8887 lbs | factorofadhesion = | operator = | operatorclass = | powerclass = | numinclass = | fleetnumbers = | officialname = | nicknames = | axleloadclass = | locale = | deliverydate = 29 November 1927 | firstrundate = 30 November 1927 | lastrundate = | retiredate = | withdrawndate = | preservedunits = | restoredate = | scrapdate = | currentowner = | disposition = | notes = }} The Harman geared locomotive was a geared locomotive by Alfred Harman from Melbourne in Australia. HistoryThe Forests Commission Victoria (FCV) called a tender for a new geared steam locomotive up to 27 May 1927.[1] The Melbourne based company of Alfred Harman issued an offer, which the FCV was obliged to accept against its better judgement, as the only suitable alternatives were made in the USA. At that time, government policy favoured the purchase of locally made machines or if these were not available, machines made in the United Kingdom.[2] The design concept was based on the use of Harman’s successful logging winches in the power bogies, but the large number of unproven design features resulted in several faults. Thus this engine had to be replaced in April 1928 by a ‘Class B’ Climax locomotive by the Climax Manufacturing Co., USA.[2] The locomotive was delivered at Moe by the Victorian Railways on 29 November 1927. It was off-loaded onto the Walhalla branch line. The following day it travelled under steam to Collins siding, in charge of a Victorian Railways crew. On arrival, it steamed over a temporary connection with the tramway and commenced the run to Tyers Junction.[3] During the problematic delivery run to Tyers Junction the engine derailed twice at 1m64c on an S-curve. The locomotive was rerailed and returned to Collins Siding, where weaker springs were installed to reduce the rigidity of the bogies. On 13 December 1927, the trip to Tyers Junction was made smoother by the use of grease on the outer rail at curves. Timber haulage commenced on 12 January 1928, after conducting modifications to the bogie masts.[3] References1. ^Tyers Valley Tramway, Victoria, Australia: The Harman geared locomotive. 2. ^1 Frank Stamford: Steam locomotives on Victorian timber tramways. In: Light Railways, 208, August 2009. 3. ^1 2 3 4 5 6 Tyers Valley Tramway, Victoria, Australia. 1 : Geared steam locomotives |
| 随便看 |
|
开放百科全书收录14589846条英语、德语、日语等多语种百科知识，基本涵盖了大多数领域的百科知识，是一部内容自由、开放的电子版国际百科全书。