词条 | 76 mm gun M1 | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
释义 |
| name = 76 mm gun M1 | image = M18 hellcat side.jpg | image_size = | caption = An M18 Hellcat armed with a 76 mm gun | origin = United States | type = Tank gun | is_explosive = | is_artillery = yes | service = | used_by = United States | wars = World War II, Korea | designer = US Ordnance Department | design_date = | manufacturer = | unit_cost = | production_date = | number = | variants = | spec_label = | weight = 1,141 lb (517.55 kg) | length = | part_length = 52 calibres | width = | height = | diameter = | breech = | recoil = | carriage = | elevation = | traverse = |caliber = {{convert|76.2|mm|in}} | filling = | filling_weight = | detonation = | yield = }} The 76 mm gun M1 was an American World War II–era tank gun developed by the U.S Ordnance Department in 1942 to supplement the 75 mm gun on the basic Medium tank M4. It was also used to arm the M18 Hellcat tank destroyer. Although the gun was tested in early August 1942 and classified on August 17, 1942,[1] it was not until August 1943[1] that the Ordnance Department developed a mounting for the M4 tank that the tank forces would accept. It was not accepted for combat until July 1944.[3] In January 1943, the decision was made to mount the 76 mm on the vehicle that would become the M18.[2] By May 1944, it was being combat tested as the T70.[3] Design and developmentThe development of a better weapon than the 75 mm gun was foreseen before the U.S. had combat experience with well-armored German tanks. The original Military specifications of 11 September 1941 for the M4 tank allowed for the mounting of numerous weapons including the 3 inch gun.[4] The first specimens of the weapon that was to become the 76 mm Gun M1 were being evaluated in August 1942 while the U.S. did not enter the ground war in the European/Africa region until Operation Torch in November 1942. The 3 inch gun was considered too heavy[4] at about {{convert|1990|lb|kg|abbr=on}}.[5] New stronger steels [6] were used to create a weapon weighing about {{convert|1200|lb|kg|abbr=on}}.[7] It was a new gun with a breech similar to that of the 75 mm M3 Gun but with a new tube (barrel and cartridge chamber) design to accommodate a new cartridge.[4] It fired the same projectiles as the {{convert|3|in|mm|adj=on}} M7 gun mounted on the 3in Gun Motor Carriage M10 tank destroyer and towed 3-inch Gun M5 anti-tank gun, but from a different cartridge case.[4] The "76-mm" designation was chosen to help keep the supply of ammunition from being confused between the two cannon.[8] The 76 mm also differed in that successive models received a muzzle brake and faster rifle twist. Aberdeen Proving Grounds began evaluations of the first test guns designated the T1 around August 1, 1942.[9] The first test guns had a bore length of 57 calibers and when tested on an M4 Sherman tank, it was then found that the long barrel caused balance problems.[4] Another T1 test gun was produced with the barrel shortened and a counterweight added to the breech to improve balance.[9] The reduction in length by {{convert|15|in|cm|abbr=off}} did not reduce performance; penetration was the same as the 3 inch gun.[10] By August 17, the Ordnance Department had classified the test gun with the shorter barrel as the 76-mm M1 [11] and set up the precedent for the designation of M4 tanks armed with the gun to include "(76M1)".[12] Tests of production M1 guns revealed that the cannon with its counterweight had issues with binding when trying to rotate the turret when the tank was resting at a steep angle. An {{convert|800|lb|abbr=on}} storage box was added to the turret rear to improve balance,[12] with evaluations held in early 1943 and the final report tendered April 1943.[13] This worked but was rejected by the Armored Forces due to the turret being cramped.[13] A more satisfactory mounting was found in August 1943 by utilizing the turret design of the T23 tank on the M4 chassis to carry the 76 mm gun.[14] The 76 mm M1A1 version of the cannon was created, having a longer recoil surface to also help with balance by permitting the placement of the trunions further up front.[14] Acceptance by the tank destroyersThe new M18 Gun Motor Carriage armed with the 76 mm was the result of the Tank Destroyers' request for such a vehicle and as such they accepted them. Acceptance for production by the tank forcesBy August 1943, the Ordnance Department M4 tank armed with 76 mm in the modified T23 turret was finally ready for production. A proposal was made by the tank forces for a test run of 1,000 tanks for combat trials and, if that was successful, then all of the M4 tank manufacturing capacity would be devoted to the 76 mm gun,[1] but this was changed to a rate that would equip 1/3 of the M4 tanks with the 76 mm gun.[15] The production proposal was part of a memo in September 1943 pointing out various flaws of the gun that made it less desirable for tank use: muzzle blast, the high explosive shell, ammunition handling, and ammunition storage. Summed up, the 76 mm offered about {{convert|1|in|mm|abbr=off}} of added armor penetrating power for a possible loss of some ground attack fire-power.[16] In a meeting in April 1944 held to discuss the assignment of the first production M4(76M1) tanks received in Britain to units, a presentation comparing the 76 mm to the 75 mm went over similar points, adding that the 76 mm was more accurate and did not have an appropriate smoke round.[28] Muzzle blastThe 76 mm obscured the target with smoke and dust. This could prevent the gunner from seeing where the projectile struck. The Ordnance Department reduced the amount of smoke by using a long primer that gave a more complete burn of the propellant before it exited the barrel.[17] The revised ammunition began to be issued for use in August 1944.[18] Later production guns were threaded for a muzzle brake to redirect the blast left and right (M1A1C and M1A2).[17] This was tested in January 1944, authorized in February 1944 with production starting June 1944. The threads of those without a brake were covered by a protector (visible in many pictures).[19] For those vehicles that did not have a muzzle brake, once the Armored Force began to accept M4s, it was recommended that tank commanders stand outside the tank and "spot" the strike of rounds to guide the gunner.[28] High-explosive capacityThe situation with the high-explosive shell was that the 3 inch M42 projectile for the 76 mm gun carried a filler of about {{convert|0.9|lb|abbr=on}} of explosives while the 75 mm gun M48 high explosive projectile carried {{convert|1.5|lb|abbr=on}}.[20] Far more high explosive ammunition was used by tankers than armor penetrating types, the ratio being about 70% HE, 20% AP and 10% smoke overall,[21] The ratio could vary by unit: From August 3 to December 31, 1944 the 13th Tank Battalion fired 55 rounds of M62 APC-T armor piercing versus 19,634 rounds of M42 high explosive.[22] Smoke ammunitionThe M88 smoke round for the 76 mm provided a "curtain" of smoke.[37] The tankers found the 75 mm M64 WP (White Phosphorus) smoke projectile useful not only for providing smoke coverage but also attacking targets including enemy tanks.[23] Some units equipped with the 76 mm preferred to maintain a 75 mm armed tank on hand to provide the M64 WP projectile.[24] Round sizeIt was thought that the longer and heavier 76 mm might hamper handling inside the tank's turret, slowing the rate of fire.[16] This may have been more of a concern than was warranted: on April 22, 1945 an M4 76-mm tank came suddenly onto a strange vehicle and the "...76 roared twice in rapid succession..." adding a friendly British scout car (waiting to ambush passers-by) to the tank's kill tally before (as the British gunner stated) "...I could lay my hand on the trigger."[25] It was also thought that the longer 76 mm would reduce ammunition capacity.[16] The 76 mm was first tested on the M4A1 series tank which carried 90 rounds of 75 mm ammunition,[26] while most other models carried 97 rounds of 75 mm.[27] The 76 mm cartridge reduced this to 83 rounds.[12] By late 1943, the Army had adopted the wet storage system of water containers among the rounds, to reduce fires and for the 76 mm gun this provided 71 rounds of ammunition, while the 75 mm could carry 104 rounds.[28] Storage depended on organization: The 76-mm T72 Gun Motor Carriage, designed to mount the 76-mm on the M10 GMC chassis in a T23 turret lightened for the job, carried 99 rounds (but not in wet storage).[29] Variants
A muzzle brake was tested in January 1944, authorized in February 1944 with production starting June 1944. Not all guns received them. The threads of those without a brake were covered by a protector visible in many pictures.[19] AmmunitionWhile the 76 mm had less High Explosive (HE) and smoke performance than the 75 mm, the higher-velocity 76 mm gave better anti-tank performance, with firepower similar to many of the armored fighting vehicles it encountered, particularly the Panzer IV tank and StuG assault gun vehicles. Using the M62 APC round, the 76 mm gun penetrated {{convert|109|mm|abbr=on}} of armor at 0° obliquity at {{convert|1000|m|abbr=on}}, with a muzzle velocity of {{convert|792|m/s|abbr=on}}. The HVAP round was able to penetrate {{convert|178|mm|abbr=on}} at {{convert|1000|m|abbr=on}}, with a muzzle velocity of {{convert|1036|m/s|abbr=on}}.[31]
The M42A1 High Explosive shell contained a {{convert|0.86|lb|kg|abbr=on}} explosive filler of TNT or a {{convert|0.85|lb|kg|abbr=on}} mixture of {{convert|0.08|lb|kg|abbr=on}} of cast TNT and {{convert|0.77|lb|kg|abbr=on}} 50/50 Amatol.[34] A reduced charge load existed with a velocity of {{convert|1550|ft/s|m/s|abbr=on}} and range of {{convert|8805|yd|m|abbr=on}}.[35] The standard M62A1 Armor Piercing Capped projectile was of the APCBC design.[33] The substitute standard M79 Armor Piercing solid monobloc shot had no filler, windscreen, or penetrating cap.[33] The M88 H.C. B.I. Smoke Shell contained a filler of H.C.[33] Based on a British design, it was intended to provide a slow-release "curtain" of smoke versus the exploding white phosphorus shell available to the 75-mm and other cannon originally designed for artillery spotting but which could also cause damaging burns.[32] The M26 brass cartridge case was used for all loaded rounds, with a weight of {{convert|5.28|lb|kg|abbr=on}} and length of {{convert|21.3|in|cm|abbr=on}}.[36] It was an entirely different case from the 3-inch MKIIM2 case used for the 3-inch M3 anti-aircraft gun and 3-inch M5, M6, and M7 guns used on the a towed anti-tank gun, M6 heavy tank, and M10 Gun Motor Carriage.[37] The 76-mm chamber capacity varied by projectile (also given is the capacities for similar 3-inch rounds to illustrate the size differences):
The 3 inch cartridge was not completely filled by the propellants used; a distance wad was used to keep the propellant pressed against the primer end.[37] By way of comparison the 75 mm M3 gun had a chamber capacity of about {{convert|88|cuin|cc|abbr=on}} for the M61 armor piercing projectile and about {{convert|80|cuin|cc|abbr=on}} for the M48 high explosive projectile [39] and the British 17pdr {{convert|300|cuin|cc|abbr=on}}.[40] Alternatives to the 76 mm M1The 76 mm M1 was a project initiated by the Ordnance Department itself.[1] Various entities suggested other weapon options which were not pursued.
US serviceThe 76-mm gun saw first use in a test batch of M18 Hellcat gun motor carriages in Italy in May 1944, under their development number T70.[45] Only the US used the M18. The moderate performance of the 76-mm cannon by 1944 standards was one of three reasons the plans for M18 production were cut from 8,986 to 2,507, of which 650 were converted to unarmed utility vehicles.[46] An experiment was performed mounting the 90-mm armed M36 turret on an M18 to provide more firepower than the 76-mm.[47] The first M4 tanks armed with 76-mms intended for combat were produced in January 1944.[48] Tanks equipped with the cannon began arriving in Britain in April 1944.[49] The issue with muzzle blast had not been addressed and higher level commanders had doubts about the use of, let alone need for, the new weapon.[49] The medium-velocity 75 mm M3 gun, which first armed the standard M4 Sherman, was quite capable of dealing with most of the German armored fighting vehicles met in 1942 and 1943 and had better ground fire capability and fewer issues with muzzle blast. It was not until July 1944 that a call for M4s armed with 76s was put out in France after unexpectedly high losses by US tank units and the arrival of numerous Panther Tanks on the US sector of the front.[43] Deliveries of the 76-mm armed tanks lagged such that by January 1945 they made up only 25% of the tanks in Europe. Plans were made by field units to directly replace the 75s on some tanks using a weight welded to the turret rear to balance it. A prototype was built, but the supply of ready-made tanks increased and that project ended.[50] The 75-mm armed M4 tanks were never completely replaced during the war with some units in Europe still having about a 50/50 mix.[51] Units in Italy readily accepted the 76-mm,[52] but were never shipped as many as desired.[44] The US units in the Pacific Theater relied mainly on the 75-mm gun.[53] The 76-mm armed M18 did see use in the Pacific late in the war.[54] British serviceThe UK had developed a more effective anti-tank cannon before the 76 mm gun became widely available. Although only slightly longer at 55 calibers, their Ordnance QF 17 pounder (76.2 mm) anti-tank gun had a much larger 76.2×583mmR cartridge case, which used about {{convert|5.5|lb|kg|abbr=on}} more propellant. The anti-tank performance of the 76mm was inferior to the British 17 pounder, more so if the latter was using APDS discarding sabot rounds, though with that ammunition the 17-pdr was less accurate than the 76mm. The 17-pounder was also much larger and had a longer recoil than the 76mm, which required a redesign of the turret and despite this, made the turret very cramped. The 17-pounder also had a less effective HE round. The 76 mm gunned Shermans supplied to the British were only used in Italy or by the Polish 1st Armoured Division in North-West Europe. The British and Commonwealth units in north-west Europe supported their 75 mm gunned Shermans with 17 pdr armed Sherman Fireflies. Russian serviceThe first 76-mm-armed Shermans started to reach Red Army units in late summer 1944. In 1945, some units were standardized to depend mostly on them, transferring their T-34s to other units. Parts of the Polish First Army also briefly used M4A2 (76 mm) tanks, borrowed from the Red Army after heavy losses in the conquest of Danzig. Post-war serviceKoreaBy the end of 1950, more than 500 76mm gun M4A3E8 tanks were in Korea. These 76-mm armed Shermans served well in the Korean War and, having better crew training and gun optics, had little problem piercing the armor of North Korean manned T-34/85 tanks when firing HVAP rounds, which were amply supplied to units.[55] Some 76-mm armed M4s [56] and M18s were distributed around the world and used by other countries post-war.[57] The 76-mm gun was sometimes replaced by a more powerful weapon.[4][55][57] Middle EastSome 76mm gun Sherman tanks were used by Israel and Arab countries. BalkansSome M4A3E4, retrofitted with the M1A1 76 mm gun, were used during the 1990s conflict in former Yugoslavia. Indo-Pak warsPakistan bought 547 M4A1E4(76)s during the 1950s and used them in 1965 and 1971 wars. UgandaUganda purchased a few ex-Israeli M4A1(76)W and used them during the Idi Amin regime. Vehicles mounted onWith British Commonwealth designations in parentheses:
Towed variantFrom 1943, at the instigation of the head of the Armored Force General Jacob Devers, US Ordnance worked on a towed anti-tank gun based on the barrel of the M1, known as "76 mm gun T2 on carriage T3". Later interest in the project declined and the program was officially cancelled in 1945.[58] Performance
See also
Weapons of comparable role, performance and era
Notes1. ^1 2 Zaloga 2003, p. 6 {{Reflist}}2. ^Zaloga 2004, p. 7 3. ^Zaloga 2004, p 14 4. ^1 2 3 4 5 6 Hunnicutt 1978, p. 198 5. ^Hunnicutt 1978, p.563 6. ^Green 1955, p. 237 7. ^1 2 3 4 5 6 7 Hunnicutt 1978, p. 564 8. ^Zaloga 2003, p. 4 9. ^1 2 Hunnicutt 1978, p. 199 10. ^{{cite web|last1=Honner|first1=David|title=USA Guns 75mm and 76mm calibre|url=http://amizaur.prv.pl/www.wargamer.org/GvA/weapons/usa_guns5.html|website=Guns Vs Armor}} 11. ^Hunnicutt 1978, p. 200 picture caption 12. ^1 2 3 4 Hunnicutt 1978, p. 200 13. ^1 Hunnicutt 1978, p. 202 14. ^1 2 Hunnicutt 1978, p. 204 15. ^Zaloga 2003, p. 8 16. ^1 2 3 Zaloga 2008, p. 116 17. ^1 2 Hunnicutt 1978, p. 206 18. ^Zaloga 2003, p. 18 19. ^1 Zaloga 2004, p. 13 20. ^Ordnance Department 1944, p. 356, 359 21. ^Zaloga 2003, p. 7 22. ^Green 2007, p. 118 23. ^Green 2007, p. 81 using the wrong designation "M89" 24. ^Zaloga 1978, p. 37-38 25. ^Hunnicutt 1978, p. 322 26. ^Hunnicutt 1978, p. 540 27. ^Hunnicutt 1978, p. 538, 542, 544, 549 28. ^Hunnicutt 1978, p. 260, 261 29. ^1 Hunnicutt 1978, p. 376 30. ^Hunnicutt 1978, p. 207 31. ^Zaloga, Steven. T-34-85 vs. M26 Pershing: Korea 1950. London: Osprey Publishing, 2010. pp. 32-33. 32. ^1 2 Leventhal 1996, p 288 33. ^1 2 3 4 Leventhal 1996, p 287 34. ^Leventhal 1996, p 287 35. ^Ordnance Department 1944, p. 128 36. ^Ordnance Department 1944, p. 124 37. ^1 Ordnance Department 1944, p. 132 38. ^Leventhal 1996, p 283,284 39. ^Hunnicutt 1978, p.562 40. ^Hunnicutt 1978, p.565 41. ^1 Hunnicutt 1978, p. 212 42. ^Zaloga 2003, p. 9 43. ^1 2 Zaloga 2003, p. 16 44. ^1 Zaloga 2003, p. 35 45. ^Zaloga 2004, p. 14 46. ^Zaloga 2004, p. 12 47. ^Zaloga 2004, p. 38 48. ^Zaloga 2003, p. 10 49. ^1 2 3 Zaloga 2003, p. 12 50. ^Zaloga 2003, p. 33 51. ^Zaloga 2003, p. 22 52. ^Zaloga 2003, p. 36 53. ^Zaloga 2003, p. 37 54. ^Zaloga 2004, p. 34 55. ^1 Zaloga 2003, p. 42 56. ^Zaloga 2003, p. 39 57. ^1 Zaloga 2003, p. 41 58. ^Zaloga 2005, p. 20 59. ^1 Steven J. Zaloga. and Peter Sarson (1993). Sherman Medium Tank. 60. ^1 2 Bovington Tank Museum (1975). Fire and Movement. 61. ^1 2 Harry Woodman (1991). Tank Armament in World War Two. 62. ^{{cite book|last1=Bird |first1=Lorrin Rexford|last2=Livingston|first2=Robert D.|title=WWII Ballistics: Armor and Gunnery|date=2001|publisher=Overmatch Press|page=63}} References
Further reading
External links{{Commons category|76 mm gun M1}}
4 : 76 mm artillery|Tank guns|World War II artillery of the United States|World War II tank guns |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
随便看 |
|
开放百科全书收录14589846条英语、德语、日语等多语种百科知识,基本涵盖了大多数领域的百科知识,是一部内容自由、开放的电子版国际百科全书。