| 词条 | In-circuit test |
| 释义 |
In-circuit test (ICT) is an example of white box testing where an electrical probe tests a populated printed circuit board (PCB), checking for shorts, opens, resistance, capacitance, and other basic quantities which will show whether the assembly was correctly fabricated.[1] It may be performed with a bed of nails type test fixture and specialist test equipment, or with a fixtureless in-circuit test setup. Bed of nails testerA bed of nails tester is a traditional electronic test fixture which has numerous pins inserted into holes in an epoxy phenolic glass cloth laminated sheet (G-10) which are aligned using tooling pins to make contact with test points on a printed circuit board and are also connected to a measuring unit by wires. Named by analogy with a real-world bed of nails, these devices contain an array of small, spring-loaded pogo pins; each pogo pin makes contact with one node in the circuitry of the DUT (device under test). By pressing the DUT down against the bed of nails, reliable contact can be quickly and simultaneously made with hundreds or even thousands of individual test points within the circuitry of the DUT. The hold-down force may be provided manually or by means of a vacuum or a mechanical presser, thus pulling the DUT downwards onto the nails. Devices that have been tested on a bed of nails tester may show evidence of this after the process: small dimples (from the sharp tips of the Pogo pins) can often be seen on many of the soldered connections of the PCB. Bed of nails fixtures require a mechanical assembly to hold the PCB in place. Fixtures can hold the PCB with either a vacuum or pressing down from the top of the PCB. Vacuum fixtures give better signal reading versus the press-down type{{Citation needed|date=February 2016}}. On the other hand, vacuum fixtures are expensive because of their high manufacturing complexity. Moreover, vacuum fixtures cannot be used on bed-of-nails systems that are used in automated production lines, where the board is automatically loaded to the tester by a handling mechanism. The bed of nails or fixture, as generally termed, is used together with an in-circuit tester. Fixtures with a grid of 0.8 mm for small nails and test point diameter 0.6 mm are theoretically possible without using special constructions. But in mass production, test point diameters of 1.0 mm or higher are normally used to minimise contact failures leading to lower remachining costs. This technique of testing PCBs is being slowly superseded by boundary scan techniques (silicon test nails), automated optical inspection, and built-in self-test, due to shrinking product sizes and lack of space on PCB's for test pads. Nevertheless ICT is used in mass production to detect failures before doing end-of-line test and producing scrap. ICT failures & mechanical simulationIn-circuit testing has been known to cause mechanical failures such as capacitor flex cracking and pad cratering. This typically occurs on a bed of nails tester if there is excessive board flexure due to poor support placement or high probe forces. It can be challenging to optimize for ideal support locations and probe forces without spending resources designing and building an ICT fixture. Current methods typically employ strain gaging or similar techniques to monitor board flexure. More recently, some have looked at finite element simulation to proactively design or adjust an ICT fixture to avoid these mechanical failure modes. This approach can be implemented as part of a design for manufacturability methodology to provide rapid feedback on ICT design and reduce costs.[2] Example test sequence
While in-circuit testers are typically limited to testing the above devices, it is possible to add additional hardware to the test fixture to allow different solutions to be implemented. Such additional hardware includes:
AdvantagesIn-circuit testing is best suited to stable products with a mature design and higher volumes.[4] It offers the following advantages:
LimitationsWhile in-circuit test is a very powerful tool for testing PCBs, it has these limitations:
Related technologiesThe following are related technologies and are also used in electronic production to test for the correct operation of Electronics Printed Circuit boards
References1. ^{{cite web|title=About Teradyne|url=http://www.teradyne.com/corp/history.html|publisher=Teradyne Corp|accessdate=28 December 2012}} 2. ^{{cite web|title=Preventing Pad Cratering During ICT Using Sherlock|url=http://www.dfrsolutions.com/hubfs/Resources/services/Preventing-Pad-Cratering-During-ICT-Using-Sherlock.pdf?hsCtaTracking=95bec082-e4c1-40d3-a379-dfe6d7a5727a%7Ce96e5f51-abc5-4c7a-9a2e-28a78cb24e8e|publisher=DfR Solutions|}} 3. ^Jun Balangue, “Successful ICT Boundary Scan Implementation,” CIRCUITS ASSEMBLY, September 2010. http://www.circuitsassembly.com/cms/magazine/208-2010-issues/10282-testinspection 4. ^{{Cite web|url=https://www.lectronics.net/best-electronic-test-solution/|title=Pick the Best Electronic Test Solution for Your Product|date=2016-06-24|website=Saline Lectronics|language=en-US|access-date=2019-02-01}} External links
3 : Printed circuit board manufacturing|Hardware testing|Electronic test equipment |
| 随便看 |
|
开放百科全书收录14589846条英语、德语、日语等多语种百科知识，基本涵盖了大多数领域的百科知识，是一部内容自由、开放的电子版国际百科全书。