| 词条 | RAF 1 | |||||||||||||
| 释义 |
The RAF 1 was a British air-cooled, V-8 engine developed for aircraft use during World War I. Based on a French design it was developed at the Royal Aircraft Factory, and built by six different British companies including Daimler, Rolls-Royce and Wolseley Motors Limited. Design and developmentThe RAF 1 was based on the Renault 70/80 hp engine, being intended specifically to replace that engine in the B.E.2c. It featured larger cylinders ({{convert|3.94|x|5.5|in|mm|abbr=on}}) for a total displacement of 540 cubic inches (8.8 L). It was rated at 92 hp (70 kW) at 1,600 rpm. The heads were cast integrally with the cylinders, with the intake and exhaust valves set one above the other in an upside-down F-head configuration. The engines featured a large diameter lightweight flywheel at the rear, enclosed in a cast housing. Engine oil was picked up from the bottom of the crankcase and slung into a reservoir at the top. From there it was gravity fed, via a gallery high on the right side of the engine block, to the main bearing caps, and then to the connecting rod journals by centrifugal effect of the turning crankshaft. The main bearings were ball bearings and were splash fed. Engine oil from the gallery was also supplied to the 1 : 2 reduction gearbox at the front. This drove the four-bladed propeller at one half engine speed, and the single camshaft was splined into the rear of the short propeller shaft. This arrangement meant that no mechanical oil pump was needed. Excess engine oil from the flywheel overflowed the reservoir and trickled over the large surface area of the round flywheel cover. Two passages cast into the cover took air-fuel mixture from the carburettor mounted at the bottom to a copper U-shaped inlet manifold mounted between the banks of cylinders, and the flywheel cover acted as a heat exchanger, preheating the fuel-air mixture. In late 1915, the bore was increased to {{convert|4.1|in|mm}}, leading to an increased displacement of 590 cubic inches (9.7 L) and power of 86 kW (115 hp) at 1,800 rpm. [1]SuperchargerIn late 1915 a supercharged experimental version of the RAF 1a was developed, the engine being flown in a B.E.2c improving the climb from taking 36 minutes to reach 8,500 ft without the supercharger, to reaching 11,500 ft in the same time.[2] VariantsRAF 1RAF 1a (standard engine for aircraft using this powerplant) RAF 1b (uprated version slated for installation in the B.E.2e - reliability problems precluded production)[3] RAF 1c RAF 1e ApplicationsList from Lumsden[1]
(For a brief period following WWI examples were fitted to several privately owned aircraft due to the engine's cheapness and comparative fuel economy - one was even found in a privately owned S.E.5a). Specifications (RAF 1a){{pistonspecs||ref=Lumsden[1] |type=8-cylinder, upright, 90 degree Vee engine |bore={{convert|3.94|in|mm|abbr=on}} |stroke={{convert|5.51|in|mm|abbr=on}} |displacement=537.4 cu in (8.8 L) |length= |diameter= |width= |height= |weight=450 lb |valvetrain= |supercharger= |turbocharger= |fuelsystem=Twin Claudel-Hobson carburettors |fueltype= |oilsystem= |coolingsystem=Air-cooled |power=108 hp at 1,800 rpm (takeoff power) |specpower= |compression=4.3:1 |fuelcon= |specfuelcon= |oilcon= |power/weight= |designer= |reduction_gear=0.5:1, Left-hand tractor |general_other= |components_other= |performance_other= }} See also{{aircontent|see also= |related=
|similar aircraft= |lists=
|similar engines=
}} ReferencesNotes1. ^1 2 Lumsden 2003, p. 223. 2. ^http://www.theaerodrome.com/forum/aircraft/50719-increasing-charge-2.html 3. ^Hare (1990) p. 115 Bibliography{{refbegin}}
1 : Aircraft piston engines 1910–1919 |
|||||||||||||
| 随便看 |
|
开放百科全书收录14589846条英语、德语、日语等多语种百科知识，基本涵盖了大多数领域的百科知识，是一部内容自由、开放的电子版国际百科全书。