1. Architect's scale
    United States and Imperial units  Metric units 

2. Engineer's scale

3. See also

4. References

5. External links

A scale ruler is a tool for measuring distances and transferring measurements at a fixed ratio of length; two common examples are an architect's scale and engineer's scale.

Architect's scale

An architect's scale is a specialized ruler designed to facilitate the drafting and measuring of architectural drawings, such as floor plans and orthographic projections. In scientific and engineering terminology, a device to measure linear distance and create proportional linear measurements is called a scale. A device for drawing straight lines is a straight edge or ruler. In common usage both are referred to as a ruler.

Because the scale of such drawings are often smaller than life-size, an architect's scale features multiple units of length and proportional length increments.

For accuracy and longevity, the material used should be dimensionally stable and durable. Scales were traditionally made of wood, but today they are usually made of rigid plastic or aluminium. Architect's scales may be flat, with 4 scales, or have a symmetric 3-lobed cross-section, with 6 scales.

United States and Imperial units

In the United States, and prior to metrification in Britain, Canada and Australia, architect's scales are/were marked as a ratio of x inches-to-the-foot (typically written as x″=1′-0″). For example, one inch measured from a drawing with a scale of "one-inch-to-the-foot" is equivalent to one foot in the real world (a scale of 1:12) whereas one inch measured from a drawing with a scale of "two-inches-to-the-foot" is equivalent to six inches in the real world (a scale of 1:6). It is not to be confused with a true unitless ratio. A 1:5 architectural scale (inches to feet) would be a 1:60 unitless scale (inches to inches) since there are 60 inches in 5 feet.

Typical scales used in the United States are:

• Full scale, with inches divided into sixteenths of an inch

The following scales are generally grouped in pairs using the same dual-numbered index line (one scale is read from the right, and the other scale is read from the left):

• three-inches-to-the-foot (3″=1′-0″) (ratio equivalent 1:4)/one-and-one-half-inch-to-the-foot ({{frac|1|1|2}}″=1′-0″) (1:8)
• one-inch-to-the-foot (1″=1′-0″) (1:12)/one-half-inch-to-the-foot ({{frac|1|2}}″=1′-0″) (1:24)
• three-quarters-inch-to-the-foot ({{frac|3|4}}″=1′-0″) (1:16)/three-eighths-inch-to-the-foot ({{frac|3|8}}″=1′-0″) (1:32)
• one-quarter-inch-to-the-foot ({{frac|1|4}}″=1′-0″) (1:48)/one-eighth-inch-to-the-foot ({{frac|1|8}}″=1′-0″) (1:96)
• three-sixteenths-inch-to-the-foot ({{frac|3|16}}″=1′-0″) (1:64)/three-thirty-seconds-inch-to-the-foot ({{frac|3|32}}″=1′0″) (1:128)

Metric units

Architect's scale rulers used in Britain and other metric countries are marked with ratios without reference to a base unit. Therefore, a drawing will indicate both its scale (ratio) and the unit of measurement being used.

In Britain, and elsewhere, the standard units used on architectural drawings are the (SI) units millimetres (mm) and metres (m), whereas in France centimetres (cm) and metres are most often used.

In Britain, for flat rulers, the paired scales often found on architect's scales are:

• 1:1/1:10
• 1:5/1:50
• 1:10/1:100
• 1:20/1:200
• 1:1250/1:2500

For triangular rulers, the paired scales are:

• 1:1/1:10
• 1:2/1:20
• 1:5/1:50
• 1:100/1:200
• 1:500/1:1000
• 1:1250/1:2500

Less common scales are:

• 1:25/1:250
• 1:33{{frac|3}}
• 2:1

Engineer's scale

An engineer's scale is a tool for measuring distances and transferring measurements at a fixed ratio of length. It is commonly made of plastic or aluminum, and is just over {{convert|12|in|mm}} long, but with only 12 inches of markings, leaving the ends unmarked so that the first and last measuring ticks do not wear off. It is used in making engineering drawings, commonly called blueprints, blue lines or plans in a specific scale. For example, "one-tenth size" would appear on a drawing to indicate a part larger than the drawing on the paper itself. It is not to be used to measure machined parts to see if they meet specifications.

In the United States this scale is divided into decimalized fractions of an inch, but has a cross-section like an equilateral triangle, which enables the scale to have six edges indexed for measurement. One edge is divided into tenths of an inch, and the subsequent ones are directly marked for twentieths, thirtieths, fortieths, fiftieths, and finally sixtieths of an inch. Referred to as 1:10, 1:20, 1:30,1:40, 1:50 or 1:60 scale. Typically in civil engineering applications, 1:10 (1″=10′) is used exclusively for detail drawings. 1:20 and 1:40 scales are used for working plans. 1:60 is normally used only to show large areas of a project.

The engineer's scale came into existence when machining parts required a greater precision than the usual, binary fractionalization of the inch, as in the architect's scale, for houses and furniture. They were used, for example, in laying out printed circuit boards with the spacing of leads from integrated circuits as one-tenth of an inch.

See also

• Technical drawing tools

References

External links

• Engineering and Architectural Scale Information

• Kenneth A. Schmied
• Kenneth A. Shaw
• Kenneth Atkins
• Kenneth Augustus Muir-Mackenzie, 1st Baron Muir-Mackenzie
• Kenneth Augustus Muir Mackenzie, 1st Baron Muir Mackenzie
• Kenneth A. Walsh
• Kenneth Baer
• Kenneth Baker
• Kenneth Baker (Metal Gear)
• Kenneth Barnard Keating
• Kenneth Barnes
• Kenneth Bartholomew
• Kenneth B. Bell
• Kenneth Beatty
• Kenneth Beaudoin
• Kenneth Belanger
• Kenneth Bell
• Kenneth Bentley Kramer
• Kenneth Bernich
• Kenneth Bi
• Kenneth Biggs
• Kenneth Bilby
• Kenneth Biller
• Kenneth Binks
• Kenneth Binmore