“UK railway signalling”的意思、由来-开放百科全书

The railway signalling system used across the majority of the United Kingdom rail network uses lineside signals to control the movement of trains.

The current system mostly uses two, three, and four aspect colour light signals using track circuit block signalling.^[1]^[2] It is a development of the original absolute block signalling that is still being used on many secondary lines. The use of lineside signals in Britain is restricted to railways with a maximum permissible speed of up to {{convert|125|mph|km/h|abbr=on}}.

Early days

In the days of the first British railways, "policemen" were employed by every railway company. Their jobs were many and varied, but one of their key roles was the giving of hand signals to inform engine drivers as to the state of the line ahead. They had no means of communication with their colleagues along the line, and trains were only protected by a time interval; after a train had passed him, a policeman would stop any following train if it arrived within (say) 5 minutes; for any between 5 and 10 minutes after, he would show a caution signal, and after 10 minutes, the line was assumed to be clear. Therefore, if a train failed midsection (as was very common in the early days), the policeman controlling entry to the section would not know, and could easily give a 'clear' signal to a following train when the section was not in fact clear. The number of collisions which resulted from this led to the gradual introduction of the absolute block principle; all systems of working other than this (including time-interval and permissive block) were outlawed on passenger lines in 1889, and all passenger lines were suitably equipped by 1895.

As train speeds increased, it became increasingly difficult for enginemen to see hand signals given by the policemen, so the railways provided various types of fixed signals to do the job, operated by the policemen, or signalmen as they soon became known (it is due to this that British railway slang still names signalmen as "Bobbies"). Many types were devised, but the most successful was the semaphore, introduced in 1841 and soon becoming widespread, although some other types did linger on until the 1890s.

Running signals

Semaphore signals

The traditional British signal is the semaphore, comprising a mechanical arm that rises or drops to indicate 'clear' (termed an "upper-quadrant" or "lower-quadrant" signal, respectively). Both types are fail safe in the event of breakage of the operating cable but lower-quadrant signals require a heavy counter-weight (usually in the form of the "spectacle" that carries the coloured lenses for use at night) to do that, while upper-quadrant signals fall back to "danger" under the weight of the arm.

During the 1870s, almost all the British railway companies standardised on the use of semaphore signals, which were then invariably of the lower quadrant type.^[3] From the 1920s onwards, upper quadrant semaphores almost totally supplanted lower quadrant signals in Great Britain, except on former GWR lines.^[4]

There are two main types of semaphore; stop and distant. The stop signal consists of a red, square-ended arm, with a vertical white stripe typically 9-12 inches (230–300 mm) from the end, and advises the driver whether the line immediately ahead is clear or not. A stop signal must not be passed in the horizontal "on" (danger) position, except where specially authorised by the signalman's instruction. By night, it shows a red light when "on" and a green light when "off" (clear). The green light is usually produced through the use of a blue spectacle lens, which produces green when lit from behind by the yellowish flame from a paraffin lamp.

The other type is the distant signal, which has a yellow arm with a 'V' ("fishtail") notch cut out of the end and a black chevron typically 9-12 inches (230–300 mm) from the end. Its purpose is to advise the driver of the state of the following stop signal(s); it may be passed in the "on" position, but the driver must slow his train to be able to stop at the next stop signal. When "off", a distant signal tells the driver that all the following stop signals of the signal box are also "off", and when "on" tells the driver that one or more of these signals is likely to be at danger. By night, it shows a yellow light when "on" and a green light when "off".

Where a signal consists of a combination of a stop and distant arms a mechanism is included to prevent the distant arm clearing while the stop arm is at ‘danger’.

Current British practice mandates that semaphore signals, both upper and lower quadrant types, are inclined at an angle of 45° from horizontal to display an "off" indication.^[5]

Colour light signals

Additionally, on the {{convert|140|mph|kph}} trial section of line between Peterborough and York:

The green aspect and the four yellow aspects are known as 'proceed aspects' as they allow the train to pass the signal; the red aspect requires the train to stop if necessary to avoid doing so.

Two-aspect systems use red and green only. Three-aspect systems include yellow. Four-aspect signalling, which also includes double yellow, is mostly used on busy routes to allow shorter headways, and on fast routes to provide longer braking distances.

Flashing yellow aspects

A flashing single or double yellow aspect indicates that a train is to take a diverging route ahead with a lower line speed than the main route. A flashing double yellow (only used in 4-aspect signalling) means that the next signal is showing flashing single yellow. A flashing single yellow means that the next signal at the junction is showing (steady) single yellow with an indication for a diverging route, and the signal beyond the junction is at danger (red).^[6] This sequence of increasingly restrictive aspects forces the driver to slow the train down in preparation for stopping at the red signal, and this ensures that the train crosses the junction safely. As the train nears the junction, the red signal beyond may 'step up' to a less restrictive aspect depending on the state of the line ahead.

The two yellows in a flashing double-yellow flash in unison rather than alternately, but the flashing double-yellow and single-yellows are not synchronised.

Failures

A failure of the changeover relay to switch on the flashing indication to the double-yellow aspect would not be a problem as it is considered a steady double-yellow followed by a flashing single-yellow aspect sequence is acceptable.

However, safety circuitry is connected to the single-yellow flashing supply to ensure that a failure of the single-yellow to change over to the flashing supply would abort the "approach release from yellow" sequence and re-impose the normal "approach control from red" sequence as failure of the single yellow to flash following a flashing double-yellow is considered potentially very dangerous.{{citation needed|date=August 2017}}

Lens placement and alignment

The design considerations determining the familiar arrangement of road signals, with red at the top, do not apply to the railway. There is only one train at any one signal, and so no need for the signal to be visible to multiple drivers along a queue of traffic; and the driver required to stop at a red aspect will normally have had clear advance warning, from the yellow aspect at the previous signal, so there is little need for the red aspect to be visible at maximum distance. Instead, on pole- and gantry-mounted railway signals the red aspect is usually positioned at the bottom. This places it closest to the driver's eyeline; it also means the red aspect cannot become obscured by snow building up on the lens hood of an aspect placed below. For corresponding reasons, on ground-mounted signals red is positioned as the highest of the principal aspects (though for example junction indicators may appear above it): again, closest to the driver's eyeline; and the risk of snow build-up on the ground obscuring the red is minimised.

On two-aspect signals the two are placed next to each other, as they are distinguished by colour rather than position. On three-aspect signals, the yellow appears between red and green, matching the natural sequence of clear - caution - stop. On four-aspect signals the two yellow aspects are separated by the green, for clarity in distinguishing the YY aspect from Y.

Variations are found according to features of track layout (junctions, crossovers, stations, bay platforms, etc.) and at interfaces between areas of, for example, three- and four-aspect systems.

In the past use was made of searchlight signals. These have a single lamp in front of which is placed either a red, yellow or green filter to show the respective aspect. The filter assembly is moved by an electro-magnet. For a double-yellow aspect a second lamp is fitted, illuminated only when required. A few traditional searchlight signals (i.e. with moving filter glasses inside) remain in use in the Clacton area. The concept had a renaissance in the 2000s with the advent of LEDs which can show three different colours.

Signal alignment is generally aimed towards a distance 200 yards (183 metres) in rear of the signal (that is, in the direction behind the driver observing it) and at a height of 2.5 to 3 m above the left hand rail. Ground mounted signals are rarely so critical for alignment (an advantage of ground mounting) and are often used in tunnels, where the relative luminosity of the aspects is much higher.

Unusual colour light aspects

Approach release

At certain locations such as the final signal on approach to a terminus station or at a diverging route requiring a large speed reduction, approach release may be used. The driver will be "checked down" with a normal signalling sequence (green, double yellow, yellow for a four-aspect area) and the red signal clears when the train is close to it. Typically for low speed junctions (e.g. {{convert|25|mph|km/h|abbr=on}} crossover on a {{convert|90|mph|km/h|abbr=on}} line), the train will be brought down to nearly standing at the signal before it clears. The control of this can be achieved by a time-delay that commences on the approaching track circuit becoming occupied. After the elapsed time, the signal is allowed to "step-up" to the highest available aspect and display the junction indicator where applicable.

Where a junction indicator is used an additional safety precaution ensures that failure of the indicator does not cause an irregular or mutilated display to appear due to partial failures of individual elements.

This can be observed in practice – at Bescot Stadium northbound the signal, when cleared for the divergence for Walsall-bound trains, shows the junction-indicator with a red aspect for 2-3 seconds before the main aspect clears – this is whilst the interlocking proves sufficient elements of the junction-indicator is lit before clearing the main aspect.

With conventional interlocking the red aspect only remains alight for a fraction of a second while the junction-indicator is proved locally. With a solid state or computerised signalling this proof has to pass through the interlocking, hence the additional time requirement.

Subsidiary signals

Subsidiary signals are those which usually control only shunting moves, as opposed to train movements. Under this category come permissive signals and shunting signals.

Semaphore subsidiary signals

Permissive signals

Although British railway operation is based on the block principle whereby only one train is allowed in a signal section, there are situations when another train must enter the section, and permissive signals are used to control that movement. There are three types of permissive semaphore: calling-on, shunt-ahead, and warning signals. Today, all three look broadly the same; they are shaped like a normal stop signal, though only about two-thirds of the size, and are painted red with a white horizontal band running centrally along them. When "on", they show a small red or white light, and when "off", they display a small green light and an illuminated 'C', 'S' or 'W', depending on their function.

Modern-day permissive signals consist of two white lights at 45°, normally unlit. When lit, with the main aspect showing red, they instruct the driver to proceed but be prepared to stop short of any obstruction. When unlit, the driver obeys the main signal aspect. They can therefore function either as calling-on or shunt-ahead signals, depending on their location (the Warning Arrangement in colour-light areas, uses the main aspect in a similar fashion to approach release junction signalling, in this case it is called a Delayed Yellow ).

The calling-on signal is by far the most common of the three types of subsidiary signal. It is mounted under the stop signal governing entry to (usually) a platform and, when pulled off, allows the driver to proceed cautiously for as far as the line is clear (or to the next stop signal). This can allow three basic moves to take place;

The shunt-ahead signal is normally mounted under the signal governing entry to the section ahead, and, as its name implies, allows a train to enter the section and clear a set of points in order to carry out a shunting move.

The warning signal is the most unusual of the three types of British permissive signal. It is, like the shunt-ahead, placed under the signal governing entry to the section ahead, but its function is very different. For a signalman to accept a train, both his block section and the line for a quarter mile inside his outer home signal must usually be clear; the quarter mile is a precaution in case the driver fails to stop in time for the outer home signal. However, it is possible to accept a train under the "Warning Arrangement" if the block section, but not the quarter-mile overlap, is clear. As its name implies, the signalman must stop and caution the driver of the train concerned, and the warning signal simply replaces the signalman's caution where this operation is frequent. Because there is no margin for braking error, the warning arrangement cannot usually be applied to passenger trains: its commonest use is to allow a goods train to run into a section to shunt a siding in the middle of that section, while a train is still occupying the station ahead.

Position light signals

Position light signals allow a train to move into a section under caution, the line ahead may be occupied so the driver must drive at a speed that enables him/her to stop short of any obstruction. Modern position lights consist of three lenses in a triangular formation.

Associated position light^[7] signals (APLS) are attached to a main aspect signal and are only illuminated when a shunting movement is permitted. When the main signal aspect is red, the position light displays two white lights at an angle of 45° indicating that the driver may pass the signal with caution. When not cleared these signals are unlit, and the train driver obeys the main aspect signal.

Ground position light^[7] signals (GPLS), are always illuminated and are located either near the ground or on a post with no corresponding main signal. They can display the following aspects:

Shunt ahead^[7] signals are fitted with either two yellow lights, or one white and one yellow light. They are usually found at the exits of marshaling yards and sidings, and can be passed at danger for a movement in the direction for which the signal cannot be cleared (e.g. into a headshunt rather than onto the main line). This arrangement prevents the signal having to be cleared every time a shunt takes place within the sidings which doesn't need to enter the running line. When cleared they allow access to the main line.

A Limit of Shunt^[8] indicator consists of two permanently lit red lights in a horizontal arrangement, meaning 'Stop'. No train is allowed to pass this signal as the direction will be against the normal direction of travel. A limit of shunt signal is permanently lit and cannot display any other aspect; there will not be a lens fitted in the proceed position on these signals.

Semaphore and Disc Shunting Signals

The mechanical equivalents of these shunting signals are found as miniature semaphores (the arms are the same size as those of permissive signals) and disc varieties (the disc is about 12 inches/30 cm diameter). The small-arm semaphores are painted in the same way as a full-size stop signal, while the discs are painted white with a red horizontal band. A small-arm semaphore shows "clear" in the same way as a full-size stop signal, while a disc rotates through 45 degrees or so when pulled off so that the red band is angled. Both display small red or green lights by night.

There are also semaphore and disc equivalents of the yellow light shunting signals; the small-arm semaphores being painted yellow with a black stripe and the discs either black or white with a yellow stripe; by night, they show small yellow lights when "on" and small green lights when "off".

Finally, instead of fixed position light signals, the Limit of Shunt may also be signalled by a simple white floodlit board on which the words "Limit of Shunt" are written in red.

Junction signals

British railway signalling is unusual in that it uses direction signalling rather than that speed signalling. A driver is informed of which route he will take at a junction, rather than the speed at which he should travel through it.

Semaphore junction signals

In semaphore areas, junctions are signalled using a series of between 2 and 5 stop signal arms on one bracket or gantry, known as splitting signals. Each arm (usually) has its own post ("doll") on the bracket, and each arm applies to one possible route. The relative heights of the posts usually convey some information about the lines to which they apply, although there is no definite standard. In some cases, the tallest post applies to the highest-speed route; in others, it applies to what the railway considered the most important route. Traditionally, splitting distant signals would be provided – a series of side-by-side distant signals telling the driver which post on the following stop signal was off; but practice since the 1920s has erred towards providing just one distant which is locked at caution if a large speed reduction is necessary. Drivers of trains must know which signal arm applies to which route, and the speed limit on that route; accidents have resulted from drivers either mis-reading splitting signals or forgetting speed restrictions, and consequently approaching junctions too fast.

Where there is a large number of possible routes, splitting signals are unsuitable because they could easily be confused, and route indicators are used instead. These consist of a black background, mounted under a single stop signal, on which is superimposed a white letter(s), number(s) or combination of the two, to make a code indicating the route to be taken. For example, if the possible routes were to Cambridge and to Norwich, a Norwich-bound train might be shown 'N' and a Cambridge-bound train 'C'. The route code is only shown when the signal is off. In semaphore areas, route indicators may be mechanical, with boards that slide into view to display the code; or electric "theatre-type", with a light projected through a suitably-printed screen.

Colour-light junction signals

The colour-light equivalent of a splitting signal is the junction indicator, colloquially known as a "lunar indicator", "feather", or "horn" in Scotland. Mounted above a colour-light signal, they consist of a row of white lights (originally a single, long, u-shaped fluorescent tube in an open-fronted case), nowadays five but traditionally three, angled to the left or right depending on the direction of the divergence.^[9]^[10] When the highest-speed route is set, the indicator is not illuminated (unless all routes are of a similar speed, in which case there is an indication for each route). When a diverging route is set, the respective junction indicator is illuminated. These can be used where there is a maximum of six routes as well as the 'straight' route, and where a maximum of three routes are to one side of the 'straight' route.

Where junction indicators are unsuitable, route indicators are also used in colour-light areas. They may take the form of a dot-matrix of white lamps, or, in more recent installations, fibre-optic displays driven from a single lamp to display the route code. At certain locations, no route indication is given for the highest-speed route. As with semaphore route indicators, they are usually restricted to areas where all routes are at low speed, often on the approach or departure from large stations.

In areas where speeds are lower and there are a number of routes which can be taken, alphanumeric (also called theatre-style) route indicators are used to display a number or a letter (e.g. a platform number or line designation) to denote the route the train is to take. They may be located above or beside the relevant signal. When a route is set and the signal is cleared, the relevant letter or number is shown. On shunting signals, where speeds are much lower, a miniature version of the alphanumeric route indicator is used.

When a route is set at a junction that involves the train taking a diverging route that must be passed at less than the mainline speed, a system known as approach release is used. There are a number of different types of approach release that are used on British railways but the most often used is approach release from red. This system has the signal before the diverging junction held at red until the train approaches it, whereupon it changes to a less restrictive aspect with the appropriate direction feather of five white lights. This is required so that the signals approaching show the correct caution aspects, slowing the train down for the junction. While the junction signal is held at red, the preceding signal will be displaying caution (yellow), and the one before that will display preliminary caution (double yellow) if it is a 4-aspect signal. This system allows for a gradual decrease in speed until a safe speed is reached for the train to move through the junction.

Another common system is approach release from yellow with flashing aspects in rear. It is essentially similar to approach release from red, except that the junction signal is released from yellow and the signals in rear will flash to warn the driver that the train will be taking a diverging route ahead. Where the turnout speed is the same as the mainline speed, approach release is not necessary.

Speed indicators

Speed indicators are displayed along a route to ensure a train does not exceed the maximum permitted speed.

Permissible speed indicators

In the UK, every section of railway line has a maximum speed, known as the Permissible speed.^[11]

Table A of the Network Rail Sectional Appendix provides a list of these. Where there is a change in permissible speed on a line, a permissible speed indicator sign will show the new speed. Train crew are expected to know every permissible speed for all the routes they work over as part of their Route knowledge. When the speed limit is increasing, the back end of the train passing must have cleared the speed limit board before the speed limit can take effect. This lowers risk of derailment.

Permissible speed indicator. This example is displaying a maximum permissible speed of {{convert|125|mph|km/h|abbr=on}}.

The number below the line always shows a higher speed and applies to passenger trains, parcel and postal trains and light locomotives, while the top figure applies to all other trains.^[12] This example therefore is displaying a maximum permissible speed of {{Convert|70|mph|km/h|abbr=on}} for passenger trains, parcel and postal trains and light locomotives, as against a maximum permissible speed of {{Convert|35|mph|km/h|abbr=on}} for all other trains.

This example is displaying a maximum permissible speed of {{convert|40|mph|km/h|abbr=on}} only for the diverging route to the left. Unless otherwise indicated with another sign, this does not apply to the current route.

Warning indicators^[13] are provided whenever there is a reduction in permissible speed of a third or more,^[13] and are placed at the service braking distance from the start of the lower speed. They are colloquially known as 'Morpeth boards', after the 1969 derailment at Morpeth, Northumberland that led to their introduction. Often, but not always, there is an AWS magnet placed before the indicator to give an audible warning to the train driver.

These indicators warn of a lower permissible speed on a route diverging ahead. This example is displaying a maximum permissible speed of {{convert|75|mph|km/h|abbr=on}} on the left diverging route. These warnings are provided whenever there is a reduction of permissible speed of a third or more, and, again, are placed at the service braking distance from the start of the lower speed.

Speed restrictions

Temporary speed restriction

When it is necessary to carry out planned maintenance or repair work on a line, a temporary speed restriction (TSR) may be installed at a particular location.^[14] Train crew are notified of this in the Network Rail issued Weekly Operating Notice, which they are required to read before they book on duty.^[15]

At the commencement of the speed restriction there is a yellow speed board, and at the end is a yellow termination board. The train cannot accelerate to the maximum permissible speed of the line until the last vehicle has passed the 'T' indicator.

When there is a station between the warning board and the commencement board, a yellow repeater warning board showing an R is positioned beyond the end of platforms to remind drivers of the restriction ahead.^[14]

If the advertised TSR is not installed, or is withdrawn earlier than planned, a yellow SPATE ('Speed previously advertised terminated early')^[14] board will be set up.

Emergency speed restriction

Network Rail will fax information about the ESR to train crew booking-on points, where it must be displayed in the red-coloured 'Late notice case'. Crews are required to check this case when signing on for duty.^[15]

If the speed restriction remains in place long enough for it to be published in the Weekly operating notice, it will become a Temporary speed restriction so the Warning indicator and its associated AWS magnet will be removed.^[16]

Blanket speed restriction

A Blanket speed restriction is used when it is necessary for trains to run more slowly over a large area.^[14] This is commonly used for weather conditions such as high winds, high temperatures or snow. No trackside signs are put out for a Blanket speed restriction, which enables it to be imposed quickly. Initially train drivers are informed directly by the signaller, and information is faxed to drivers' booking on points where it is posted on the Late notice board.^[15]

Other signals

Off Indicator: An illuminated off indication means the associated signal is showing a proceed aspect. These are mainly used at stations, for the benefit of the train-crew and platform staff. When the display is blank, it means that the associated signal is at danger. An illuminated indication CD (close doors) is an instruction to close the train's power-operated doors. An illuminated indication RA or R (right away) means that station duties are complete and the train may depart.

A SPAD indicator^[19] is a separate indicator which may be positioned after a main signal where there is a likelihood of a serious collision at a junction if a SPAD (signal passed at danger) occurs at the main signal. SPAD indicators are mounted against a blue backplate or surround. They are normally unlit but following a SPAD they display a steady red light between two flashing red lights arranged vertically. Any driver who sees a SPAD indicator illuminated must stop their train immediately, even if they can see that the signal pertaining to their line is showing a proceed aspect.

Banner repeating signals

Banner repeating signals^[30] are provided on the approach to certain signals which have restricted sighting (for example because of

curvature of the line, buildings or tunnels), to give advance information of the signal aspect. Their meanings are^[20]

Obsolete signals

Purple lights

Three-position semaphore signals

From 1914, a small number of British installations used motor-operated three-position semaphore signals of North American origin. These worked in the upper quadrant to distinguish them from the two-position lower quadrant semaphores that were standard at the time of their introduction. When the arm was inclined upwards at 45°, the meaning was "caution" and the arm in the vertical position meant "clear". Thus, three indications could be conveyed with just one arm and without the need for a distant arm on the same post.

Euston to Watford experimental system

This scheme, on the face of it, was a fairly standard colour light system, with each stop signal (which could show red or green) having an attendant repeater signal (showing red, yellow or green – the red used only for when the two stop signals on either side were also red). What made the scheme unusual was the provision of an automatic 'calling on' facility. The stop signals had an additional signal head ('marker light') that featured a red aspect plus a miniature yellow aspect. This marker light was mounted part way up the post. On repeater signals, the marker light was offset to the left-hand side of the post to indicate that the 'stop and proceed' rule applied. Junction stop signals were provided with two main signal heads, one mounted higher than the other. Splitting distant signals had three main heads, the centre one mounted higher than the other two.

When a train stopped at a red stop signal, its presence on the track started a time delay relay. At the conclusion of the time delay, the red marker light was extinguished and replaced by the miniature yellow (the upper red aspect remained lit). The train stop also lowered. The calling on aspect authorised the driver to proceed, but to be prepared to stop short of another train.

The scheme was not considered a great success. In fact, during periods of severe service disruption, it was not unusual to see several trains buffer-to-buffer along the line, though this occurred when the line was much busier than now. Concern was expressed that similar coloured aspects had different interpretations depending on where on the signal they appeared.

The system was finally identified for replacement following an accident at Kensal Green, when a main line train ran into the back of Bakerloo Line train.^[22] The driver had apparently mistaken the calling on aspect for a normal yellow aspect (the signal was temporarily operating on a maximum yellow due to track side work). The indications were that the driver was distracted as his pay slip and its envelope were recovered from the wreckage – but this was never proved as the cause. It was also suggested that the driver may not even have checked the indications having observed the fall of the train stop. The entire line was resignalled to the standard colour light system in 1988.

Warning systems

Because of the propensity for heavy fog in some parts of the British Isles, fog signal rules were established on the UK railway system to keep train traffic moving without incurring the severe delays that would be necessary if drivers had to stop or travel slowly up to each signal and read its indication. During heavy fog, fogsignalmen would be stationed at distant signals with a lantern and detonators – small explosive charges that could be strapped to the rail to be exploded by the wheels of a train. The fogsignalman's duty was to repeat the indication of the signal using his lantern; the semaphore arm was usually obscured by fog and hence invisible to the driver of a moving train. If the distant signal were displaying 'caution' (warning that a signal ahead was at 'danger'), the detonators remained on the rail and the fogsignalman would show a yellow lamp to show 'caution'; if the distant signal were clear, the detonators would be removed from the rails and a green lamp would be displayed.

Britain's Great Western Railway introduced the Automatic Train Control (ATC) system in 1906. This system is the forerunner of today's Automatic Warning System (AWS) and consists of an electrical system that sounded a bell in the cab as the train approached a signal at clear. Power was fed through a metal ramp to a pickup on the underside of the locomotive to power the bell. An absence of the electrical voltage on the ramp caused a warning horn to sound in the locomotive's cab. The driver then had a set time to acknowledge the warning and start braking his train accordingly. If the driver did not acknowledge the warning, the brakes would be applied automatically. Where this was implemented, it did away with the need for fog signalling, since the driver could tell the state of the distant signal regardless of his ability to see it.

The current system of AWS in use on Britain's railways is similar in principle to the Great Western's ATC but does not rely on physical contact between the track equipment and the train; instead an inductive system is used.

On passenger lines, AWS is now often supplemented by the Train Protection & Warning System (TPWS). TPWS will automatically apply the train's brakes in the event of a fitted signal being passed at danger without authority.