| 词条 | Ultra-linear |
| 释义 |
Ultra-linear electronic circuits are those used to couple a tetrode or pentode vacuum-tube (also called "electron-valve") to a load (e.g. to a loudspeaker). 'Ultra-linear' is a special case of 'distributed loading'; a circuit technique patented by Alan Blumlein in 1937 (Patent No. 496,883), although the name 'distributed loading' is probably due to Mullard.[1] In 1938 he applied for the US patent 2218902. The particular advantages of ultra-linear operation, and the name itself, were published by David Hafler and Herbert Keroes in the early 1950s through articles in the magazine "Audio Engineering" from the USA.[2] The special case of 'ultra linear' operation is sometimes confused with the more general principle of distributed loading. OperationA pentode or tetrode vacuum-tube (valve) configured as a common-cathode amplifier (where the output signal appears on the plate) may be operated as:
The impression of any portion of the output signal onto the screen-grid can be seen as a form of feedback, which alters the behaviour of the electron stream passing from cathode to anode. AdvantagesBy judicious choice of the screen-grid percentage-tap, the benefits of both triode and pentode vacuum-tubes can be realised. Over a very narrow range of percentage-tapping, distortion is found to fall to an unusually low value—sometimes less than for either triode or pentode operation[2]—while power efficiency is only slightly reduced compared with full pentode operation. The optimum percentage-tap to achieve ultra-linear operation depends mainly on the type of valve used; a commonly seen percentage is 43% (of the number of transformer primary turns on the plate-circuit) which applies to the KT88, although many other valve types have optimum values close to this. A value of 20% was recommended for 6V6GTs. Mullard circuits such as the 5-20 also used 20% distributed loading (but did not achieve ultra-linear operation), while LEAK amplifiers used 50%. The characteristics of the circuit which make distributed loading suitable for audio power amplifiers, when compared to a tetrode or pentode amplifier, are:
The distributed load circuit may be applied to either push-pull or single-ended amplifier circuits. Note that the term 'ultra linear' was expressly reserved only for the condition of optimum tapping point. As Hafler and Keroes wrote: "Our patent claims cover the use of any primary tap in this circuit arrangement. However, we have restricted the use of the term "Ultra Linear" to the conditions where the dynamic plate characteristic curves are most linear".[3] Related circuitsThe "QUAD II" amplifier from QUAD uses a circuit in which the cathode has a portion of the output signal applied to it, and was referred to as "distributed load" by Peter Walker of QUAD. In the United States, McIntosh Laboratories used this technique extensively in their vacuum-tube power amplifiers. Audio Research Corp have also used a similar circuit. References1. ^{{Cite book |author=Mullard Ltd. |year=1959 |title=Mullard Circuits for Audio Amplifiers}} 2. ^1 {{Citation |last1=Hafler |first1=David |last2=Keroes |first2=Herbert I |date=November 1951 |title=An Ultra-Linear Amplifier |journal=Audio Engineering |pages=15–17 |url=http://www.aikenamps.com/images/Documents/UL.pdf |archiveurl=http://www.tubecad.com/Classic_Articles/page2.html |archivedate=2000}}. 3. ^{{Citation |last1=Hafler |first1=David |last2=Keroes |first2=Herbert I. |date=September 1952 |title=Ungilding the Lily (letter) |journal=Audio Engineering |page=8 |url=http://dalmura.com.au/projects/Gilding%20the%20Lily%20-%20July%201952%20-%20Audio.pdf |accessdate=2014-07-17}} 2 : Vacuum tubes|Electronic amplifiers |
| 随便看 |
|
开放百科全书收录14589846条英语、德语、日语等多语种百科知识，基本涵盖了大多数领域的百科知识，是一部内容自由、开放的电子版国际百科全书。