词条 | Zero-stage |
释义 |
At a given core size, adding a stage to the front of the compressor not only increases the cycle overall pressure ratio, but increases the core mass flow. A further uprating may be done by adding another stage in front of the previously-added zero stage, in which case the new one may be known as a zero-zero stage. A comparison with other ways of uprating an existing engine without drastically redesigning the engine shows for a particular case, e.g. the Rolls-Royce/SNECMA M45H, the thrust could have been increased by 25% with a zero-staged l-p compressor or 10% with either an improved HP turbine or with water injection.[3] Zero-staging is also combined with other modifications to provide increased thrust or lower turbine temperature.[4] It may be required for an existing aircraft weight increase, or for a new application, as shown by the following examples. A 15-stage Rolls-Royce Avon powered the Lightning F.1. A zero-stage, together with a new turbine, was added (total 16 stages) for the Caravelle III. A zero-zero stage was added (total 17 stages) for the Caravelle VI.[4] The 7-stage Snecma Atar D was used in the Mystere II. A zero-stage was added (total 8 stages) for the E and G used in the Vautour and Super Mystere B.2. A zero-zero stage (total 9 stages), together with a 2-stage turbine was added for the Atar 8 and 9 used in the Mirage III.[5] The Rolls-Royce/Snecma Olympus 593 started with a 6-stage LP compressor. As the Concorde increased in weight during the design phase the take-off thrust requirement increased. The engine was given a zero-stage to the compressor, a redesigned turbine and partial reheat.[2] Examples of zero-staging for land-based gas turbines are the aeroderivative GE LM2500+[6] and the heavy-duty GE MS5002B.[7] An alternative to zero-staging used by some OEMs is supercharging the compressor with a fan driven by an electric motor.[8] Zero-staging is demonstrated by the following relationship: where: core mass flow = core size = core total head pressure ratio = inverse of core total head temperature ratio = i.e. () core entry total pressure = core entry total temperature = So basically, increasing increases . On the other hand, adding a stage to the rear of the compressor increases overall pressure ratio, and decreases core size, but has no effect on core flow. This option also needs a Turbine with a significantly smaller flow capacity to drive the compressor. References1. ^"Optimization Of Military Compressors For Weight and Volume" Keith Garwood, AGARD-CP-421, Propulsion and Energetics Panel 69th Symposium, Paris, 4-8 May 1987 {{engine-aircraft-stub}}2. ^1 Hooker, Sir Stanley (1984). Not much of an Engineer, P. 153. Airlife Publishing Ltd, Shrewsbury, England {{ISBN|0906393353}}. 3. ^https://www.flightglobal.com/pdfarchive/view/1974/1974%20-%200622.html 4. ^1 ""Rolls-Royce Aero Engines" Bill Gunston, Patrick Stephens Limited 1989, {{ISBN|1-85260-037-3}}, p.141-142 5. ^https://www.flightglobal.com/pdfarchive/view/1959/1959%20-%200803.html 6. ^http://www.ewp.rpi.edu/hartford/~roberk/IS_Climate/Papers/T36-TUT02.pdf 7. ^https://powergen.gepower.com/content/dam/gepower-pgdp/global/en_US/documents/technical/ger/ger-4171-perf-reliability-improvements-ms5002-gas-turbines.pdf 8. ^http://www.fernengineering.com/pdf/gt_upgrade_options.pdf 1 : Jet engines |
随便看 |
|
开放百科全书收录14589846条英语、德语、日语等多语种百科知识,基本涵盖了大多数领域的百科知识,是一部内容自由、开放的电子版国际百科全书。