“Hybrid physical–chemical vapor deposition”的意思、由来-开放百科全书

词条

Hybrid physical–chemical vapor deposition

释义

System configuration
Magnesium diboride thin films by HPCVD
Principle Pure films Carbon-alloyed films
See also
References

Hybrid physical–chemical vapor deposition (HPCVD) is a thin-film deposition technique, that combines physical vapor deposition (PVD) with chemical vapor deposition (CVD).

For the instance of magnesium diboride (MgB₂) thin-film growth, HPCVD process uses diborane (B₂H₆) as the boron precursor gas, but unlike conventional CVD, which only uses gaseous sources, heated bulk magnesium pellets (99.95% pure) are used as the Mg source in the deposition process. Since the process involves chemical decomposition of precursor gas and physical evaporation of metal bulk, it is named as hybrid physical–chemical vapor deposition.

System configuration

The HPCVD system usually consists of a water-cooled reactor chamber, gas inlet and flow control system, pressure maintenance system, temperature control system and gas exhaust and cleaning system.

The main difference between HPCVD and other CVD systems is in the heating unit. For HPCVD, both substrate and solid metal source are heated up by the heating module. The conventional HPCVD system usually has only one heater. The substrate and solid metal source sit on the same susceptor and are heated up inductively or resistively at the same time. Above certain temperature, the bulk metal source melts and generates a high vapor pressure in the vicinity of the substrate. Then the precursor gas is introduced into the chamber and decomposes around the substrate at high temperature. The atoms from the decomposed precursor gas react with the metal vapor, forming thin films on the substrate. The deposition ends when the precursor gas is switched off. The main drawback of single heater setup is the metal source temperature and the substrate temperature cannot be controlled independently. Whenever the substrate temperature is changed, the metal vapor pressure changes as well, limiting the ranges of the growth parameters. In the two-heater HPCVD arrangement, the metal source and substrate are heated up by two separate heaters. Thus it can provide more flexible control of growth parameters.

Magnesium diboride thin films by HPCVD

HPCVD has been the most effective technique for depositing magnesium diboride (MgB₂) thin films. Other MgB₂ deposition technologies either have a reduced superconducting transition temperature and poor crystallinity, or require ex situ annealing in Mg vapor. The surfaces of these MgB₂ films are rough and non-stoichiometric. Instead, HPCVD system can grow high-quality in situ pure MgB₂ films with smooth surfaces, which are required to make reproducible uniform Josephson junctions, the fundamental element of superconducting circuits.

Principle

From the theoretical phase diagram of Mg-B system, a high Mg vapor pressure is required for the thermodynamic phase stability of MgB₂ at elevated temperature. MgB₂ is a line compound and as long as the Mg/B ratio is above the stoichiometric 1:2, any extra Mg at elevated temperature will be in the gas phase and be evacuated. Also, once MgB₂ is formed, it has to overcome a significant kinetic barrier to thermally decompose. So one does not have to be overly concerned about maintaining a high Mg vapor pressure during the cooling stage of the MgB₂ film deposition.

Pure films

During the growth process of magnesium diboride thin films by HPCVD, the carrier gas is purified hydrogen gas H₂ at a pressure of about 100 Torr. This H₂ environment prevents oxidation during the deposition. Bulk pure Mg pieces are placed next to the substrate on the top of the susceptor. When the susceptor is heated to about 650 °C, pure Mg pieces are also heated, which generates a high Mg vapor pressure in the vicinity of the substrate. Diborane (B₂H₆) is used as the boron source. MgB₂ films starts to grow when the boron precursor gas B₂H₆ is introduced into the reactor chamber. The growth rate of the MgB₂ film is controlled by the flow rate of B₂H₆/H₂ mixture. The film growth stops when the boron precursor gas is switched off.

Carbon-alloyed films

To improve the performance of superconducting magnesium diboride thin films in magnetic field, it is desirable to dope impurities into the films. The HPCVD technique is also an efficient method to grow carbon-doped or carbon-alloyed MgB₂ thin films. The carbon-alloyed MgB₂ films can be grown in the same way as the pure MgB₂ films deposition process described above except adding a metalorganic magnesium precursor, bis(methylcyclopentadienyl)magnesium precursor, into the carrier gas. The carbon-alloyed MgB₂ thin films by HPCVD exhibit extraordinarily high upper critical field (H_c2). H_c2 over 60 T at low temperatures is observed when the magnetic field is parallel to the ab-plane.

References

{{cite paper | author = X.H. Zeng et al.,| title = In situ epitaxial MgB₂ thin films for superconducting electronics | date = 2002 | publisher = Nature Materials 1, 35–38}}
{{cite paper | author = X.X. Xi et al., | title = MgB₂ thin films by hybrid physical–chemical vapor deposition |date = 2007 | publisher = Physica C 456, 22–37}}

2 : Thin film deposition|Coatings

随便看