| 词条 | Medium access control |
| 释义 |
In IEEE 802 LAN/MAN standards, the medium access control (MAC) sublayer (also known as the media access control sublayer) and the logical link control (LLC) sublayer together make up the data link layer. Within that data link layer, the LLC provides flow control and multiplexing for the logical link (i.e. EtherType, 802.1Q VLAN tag etc), while the MAC provides flow control and multiplexing for the transmission medium. These two sublayers together correspond to layer 2 of the OSI model. For compatibility reasons, LLC is optional for implementations of IEEE 802.3 (the frames are then "raw"), but compulsory for implementations of all other IEEE 802 standards. Within the hierarchy of the OSI model and IEEE 802 standards, the MAC block provides a control abstraction of the physical layer such that the complexities of physical link control are invisible to the LLC and upper layers of the network stack. Thus any LLC block (and higher layers) may be used with any MAC. In turn, the medium access control block is formally connected to the PHY via a media-independent interface. Although the MAC block is today typically integrated with the PHY within the same device package, historically any MAC could be used with any PHY, independent of the transmission medium. When sending data to another device on the network, the MAC block encapsulates higher-level frames into frames appropriate for the transmission medium (i.e. the MAC adds a syncword preamble and also padding if necessary), adds a frame check sequence to identify transmission errors, and then forwards the data to the physical layer as soon as the appropriate channel access method permits it. Controlling when data is sent and when to wait is necessary to avoid congestion and collisions, especially for topologies with a collision domain (bus, ring, mesh, point-to-multipoint topologies). Additionally, the MAC is also responsible for compensating for congestion and collisions by initiating retransmission if a jam signal is detected, and/or negotiating a slower transmission rate if necessary. When receiving data from the physical layer, the MAC block ensures data integrity by verifying the sender's frame check sequences, and strips off the sender's preamble and padding before passing the data up to the higher layers. {{Multiplex techniques}}Functions performed in the MAC sublayerAccording to IEEE Std 802-2001 section 6.2.3 "MAC sublayer", the primary functions performed by the MAC layer are:[1]
In the case of Ethernet, according to 802.3-2002 section 4.1.4, the functions required of a MAC are:[2]
Addressing mechanismThe local network addresses used in IEEE 802 networks and FDDI networks are called media access control addresses; they are based on the addressing scheme that was used in early Ethernet implementations. A MAC address is intended as a unique serial number. MAC addresses are typically assigned to network interface hardware at the time of manufacture. The most significant part of the address identifies the manufacturer, who assigns the remainder of the address, thus provide a potentially unique address. This makes it possible for frames to be delivered on a network link that interconnects hosts by some combination of repeaters, hubs, bridges and switches, but not by network layer routers. Thus, for example, when an IP packet reaches its destination (sub)network, the destination IP address (a layer 3 or network layer concept) is resolved with the Address Resolution Protocol for IPv4, or by Neighbor Discovery Protocol (IPv6) into the MAC address (a layer 2 concept) of the destination host. Examples of physical networks are Ethernet networks and Wi-Fi networks, both of which are IEEE 802 networks and use IEEE 802 48-bit MAC addresses. A MAC layer is not required in full-duplex point-to-point communication, but address fields are included in some point-to-point protocols for compatibility reasons. Channel access control mechanismThe channel access control mechanisms provided by the MAC layer are also known as a multiple access protocol. This makes it possible for several stations connected to the same physical medium to share it. Examples of shared physical media are bus networks, ring networks, hub networks, wireless networks and half-duplex point-to-point links. The multiple access protocol may detect or avoid data packet collisions if a packet mode contention based channel access method is used, or reserve resources to establish a logical channel if a circuit-switched or channelization-based channel access method is used. The channel access control mechanism relies on a physical layer multiplex scheme. The most widespread multiple access protocol is the contention based CSMA/CD protocol used in Ethernet networks. This mechanism is only utilized within a network collision domain, for example an Ethernet bus network or a hub-based star topology network. An Ethernet network may be divided into several collision domains, interconnected by bridges and switches. A multiple access protocol is not required in a switched full-duplex network, such as today's switched Ethernet networks, but is often available in the equipment for compatibility reasons. Channel access control mechanism for concurrent transmissionUse of directional antennas and millimeter-wave communication in a wireless personal area network increases the probability of concurrent scheduling of non‐interfering transmissions in a localized area, which results in an immense increase in network throughput. However, the optimum scheduling of concurrent transmission is an NP-hard problem.[3] Cellular networksCellular networks, such as GSM, UMTS or LTE networks, also use a MAC layer. The MAC protocol in cellular networks is designed to maximize the utilization of the expensive licensed spectrum. [4] The air interface of a cellular network is at layers 1 and 2 of the OSI model; at layer 2, it is divided into multiple protocol layers. In UMTS and LTE, those protocols are the Packet Data Convergence Protocol (PDCP), the Radio Link Control (RLC) protocol, and the MAC protocol. The base station has the absolute control over the air interface and schedules the downlink access as well as the uplink access of all devices. The MAC protocol is specified by 3GPP in TS 25.321[5] for UMTS, TS 36.321[6] for LTE and TS 38.321[7] for 5G New Radio (NR). See also
References1. ^{{cite web |url=http://standards.ieee.org/getieee802/download/802-2001.pdf |title=IEEE 802-2001 (R2007) IEEE Standard for Local and Metropolitan Area Networks: Overview and Architecture |publisher=IEEE}} 2. ^{{cite web |url=http://standards.ieee.org/about/get/802/802.3.html |title=IEEE 802.3 |publisher=IEEE}} 3. ^{{cite journal|author=Bilal, Muhammad|displayauthors=etal|title=Time‐Slotted Scheduling Schemes for Multi‐hop Concurrent Transmission in WPANs with Directional Antenna|journal=ETRI Journal |volume=36|issue=3|pages=374–384|arxiv=1801.06018|doi=10.4218/etrij.14.0113.0703|year=2014}} 4. ^{{cite book|author1=Guowang Miao|author2=Jens Zander|author3=Ki Won Sung|author4=Ben Slimane|title=Fundamentals of Mobile Data Networks|publisher=Cambridge University Press|isbn=978-1107143210|year=2016}} 5. ^3GPP TS 25.321 Medium Access Control (MAC) protocol specification 6. ^3GPP TS 36.321 Evolved Universal Terrestrial Radio Access (E-UTRA); Medium Access Control (MAC) protocol specification 7. ^3GPP TS 38.321 NR; Medium Access Control (MAC) protocol specification
2 : Media access control|Link protocols |
| 随便看 |
|
开放百科全书收录14589846条英语、德语、日语等多语种百科知识，基本涵盖了大多数领域的百科知识，是一部内容自由、开放的电子版国际百科全书。