| 词条 | Triplex (locomotive) |
| 释义 |
A Triplex locomotive is a steam locomotive that divides the driving force on its wheels by using three pairs of cylinders rigidly mounted to a single locomotive frame. Inevitably any such locomotive will be articulated. All the examples that have been produced have been of the Mallet type but with one extra set of driving wheels under the tender. Triplex classesBaldwin Locomotive Works built three 2-8-8-8-2 locomotives for the Erie Railroad between 1914 and 1916. Numbers #5014–5016. One, #5014, was named "Matt H. Shay". These engines rarely made a maximum speed of 10 miles per hour. The Erie Railroad scrapped their Triplexes from 1929, 1931, and 1933.[1] One 2-8-8-8-4 was also built, for the Virginian Railway as # 700 in 1916. This was class XA, so named due to the experimental nature of the locomotive. The 2-8-8-8-4 was highly unsuccessful because of only making a maximum speed of 3–5 miles per hour and high maintenance costs. The firebox was almost the same size as the small boiler! The XA was sent back to Baldwin Locomotive Works in 1920 to be converted to a 2-8-8-0 and a 2-8-2. These two engines were up in service until 1953. None of the two engines were preserved. There was also a proposal for a quadruplex super Garratt locomotive with a 2-6-6-2+2-6-6-2 wheel arrangement for South African Railways, but this was never built.[2] UsageThe purpose of the Triplexes was banking[1] heavy trains over steep inclines, requiring high tractive effort, but low speed, over short distances. The center set of cylinders received high-pressure steam. The exhaust from these was fed to the two other sets of cylinders, which were valved for low pressure.[1] The right cylinder exhausted into the front set of low pressure cylinders, and the left into the rear set; this is also why the high pressure cylinders have the same diameter as the low pressure ones, whereas most mallet locomotives have much smaller high pressure cylinders. The front set exhausted through the smokebox and the rear set exhausted first through a feedwater heater in the tender and then to the open air through a large pipe, which can be seen in the photo. Since only half of the exhaust steam exited through the smokebox, firebox draft (and thus boiler heating) was poor. Although the boiler was large (in line with contemporary two-cylinder and four-cylinder practice), six large cylinders demanded more steam than even such a boiler could supply.[1] With all six cylinders operating at their full pressure (which could not be sustained for very long), the Triplexes produced huge amounts of tractive effort (TE) that may have been the highest of any steam locomotives before or since. (Westing[1] gives a figure of {{convert|160000|lbf|kN|abbr=on|disp=sqbr}} in compound mode and seems to indicate that it was the largest TE for any locomotive up to the time [1914–1916].) The Triplexes could also be considered the largest tank engines ever built since the tender had driving wheels as well and thus contributed to traction. The problem of variable adhesion on the tender unit was not a serious one, since pusher locomotives had frequent opportunities to take on additional fuel and water. In total, only four Triplexes came into existence and only in the United States; all were retired by 1930; none were preserved. References1. ^1 2 3 4 {{Harvnb|Westing|1966|pp=124–125}}. 2. ^Leslie Paxton and David Bourne, Locomotive of the South African Railways, Struik, 1985, pp. 8–9. Bibliography
External links
1 : Steam locomotive types |
| 随便看 |
|
开放百科全书收录14589846条英语、德语、日语等多语种百科知识，基本涵盖了大多数领域的百科知识，是一部内容自由、开放的电子版国际百科全书。