请输入您要查询的百科知识:

 

词条 Santoku
释义

  1. Design

  2. Variations

  3. See also

  4. References

  5. External links

{{Italic title|reason=Category:Japanese words and phrases}}

The Santoku bōchō (Japanese: 三徳包丁; "three virtues" or "three uses") or Bunka bōchō (文化包丁) is a general-purpose kitchen knife originating in Japan. Its blade is typically between 13 and 20 cm (5 and 8 in) long, and has a flat edge and a sheepsfoot blade that curves in an angle approaching 60 degrees at the point. The word refers to the three cutting tasks which the knife performs well: slicing, dicing, and mincing. The Santoku's blade and handle are designed to work in harmony by matching the blade's width/weight to the weight of blade tang and handle, as with the original Japanese Santoku.[1]

Design

Santoku blade geometry incorporates the sheep's foot tip. A sheep's foot design essentially draws the spine ("backstrap") down to the front, with very little clearance above the horizontal cutting plane when the blade is resting naturally from heel to forward cutting edge. Providing a more linear cutting edge, the Santoku has limited "rocking" travel (in comparison to a German/Western-style chef's knife). The Santoku may be used in a rocking motion; however, very little cutting edge makes contact with the surface due to the extreme radius of the tip and very little "tip travel" occurs due to the short cantilever span from contact landing to tip. An example of this limitation can be demonstrated in dicing an onion—a Western knife generally slices downward and then rocks the tip forward to complete a cut; the Santoku relies more on a single downward cut and even landing from heel to tip, thus using less of a rocking motion than Western style cutlery.

The Santoku design is shorter, lighter, thinner, and more hardened steel in the tradition of Samurai sword steel (to compensate for thinness) than a traditional Western chef's knife. Standard Santoku blade length is between {{convert|6|and|7|in|cm|order=flip|0|abbr=on}}, in comparison to the typical {{convert|8|in|cm|order=flip|0|abbr=on}} home cook's knife. Most classic kitchen knives maintain a blade angle between 40 and 45 degrees (a bilateral 20 to 22.5 degree shoulder, from cutting edge); Japanese knives typically incorporate a chisel-tip (sharpened on one side), and maintain a more extreme angle (10 to 15 degree shoulder). A classic Santoku will incorporate the Western-style, bilateral cutting edge, but maintain a more extreme 12 to 15 degree shoulder, akin to Japanese cutlery. It is critical to increase the hardness of Santoku steel so edge retention is maintained and "rolling" of the thin cutting edge is mitigated. However, harder, thinner steel is more likely to chip, when pushing against a bone for example. German knives use slightly "softer" steel, but have more material behind their cutting edge. For the average user, a German-style knife is easier to sharpen, but a Santoku knife, if used as designed, will hold its edge longer. With few exceptions, Santoku knives typically have no bolster, sometimes incorporate "scalloped" sides, also known as a Granton edge, and maintain a more uniform thickness from spine to blade.

Variations

Some of the knives employ San Mai laminated steels, including the pattern known as suminagashi (墨流し literally, "flowing-ink"). The term refers to the similarity of the pattern formed by the blade's damascened and multi-layer steel alloys to the traditional Japanese art of suminagashi marbled paper. Forged laminated stainless steel cladding is employed on better Japanese Santoku knives to improve strength and rust resistance while maintaining a hard edge. Knives possessing these laminated blades are generally more expensive and of higher quality.

There are many copies of Santoku-pattern knives made outside of Japan that have substantially different edge designs, different balance, and different steels than the original Japanese Santoku. One trend in Santoku copies made of a single alloy is to include scallops or recesses, hollowed out of the side of blade, similar to those found in meat-carving knives. These scallops create small air pockets between the blade and the material being sliced in an attempt to improve separation and reduce cutting friction.

See also

  • Japanese cutlery
  • Chef's knife
  • Kitchen knife
  • Kitchen knife indentation

References

External links

  • "[https://www.americastestkitchen.com/videos/841-santoku-knives Equipment Corner: Do You Really Need a Santoku Knife?]". Episode "[https://www.americastestkitchen.com/episode/20-bistro-classics Bistro Classics]." America's Test Kitchen TV show. 2005 Season. Viewed April 3, 2005.
  • [https://www.youtube.com/watch?v=JhvmKJZ5YoE How to Use the Shun Hiro Santoku Knife - Chris Cosentino by Williams-Sonoma 4:23]
  • [https://www.youtube.com/watch?v=RnSgPpKGwh0 French Chef Knife vs Santoku] - YouTube
{{Commons category|Santoku knives}}{{Knives}}

2 : Kitchen knives|Japanese kitchen knives

随便看

 

开放百科全书收录14589846条英语、德语、日语等多语种百科知识,基本涵盖了大多数领域的百科知识,是一部内容自由、开放的电子版国际百科全书。

 

Copyright © 2023 OENC.NET All Rights Reserved
京ICP备2021023879号 更新时间:2024/9/23 7:30:37