“RRG Urubu Obs”的意思、由来-开放百科全书

Design and development

In 1931 Professor Walter Georgii, an academic meteorologist and head of the Rhön-Rossitten Gesellschaft (RRG) asked Alexander Lippisch to design a glider for meteorological research. In addition to the pilot, space was required for two observers or, more usually, one with a variety of meteorological instruments, so the Urubu Obs had to be a large glider.

Its wooden high gull wing had a rectangular centre section, occupying about 20% of the overall {{convert|26|m|ftin|abbr=on|0}} span and mounted with marked dihedral. On each side a pair of rearwards leaning N-form lift struts braced the end of this section to the lower fuselage longeron. The outer panels had no dihedral and were strongly straight tapered, with a taper ratio of 1:4.7, though the trailing edges were unswept. They were also strongly tapered in thickness. Its large area wing and consequent low wing loading meant the Obs flew slowly. The thin, narrow chord wing tips carried endplate fins; like those on some of Lippisch's Storch tailless gliders, these carried rudders that were coupled to the conventional rear rudder, assisting it and allowing the Obs to have a short fuselage. The trailing edge of each outer panel carried three equal span ailerons. The outer one, together with that on the other wing, acted as differential ailerons but the inner pair also served as camber changing flaps. There is some doubt whether or not the wing was fitted with inboard upper surface airbrakes; these may have been added as a result of test flying.^[3]

The Obs had a rectangular section, steel tube framed, fabric covered fuselage. Its cockpit, under a multi-piece canopy was ahead of the forward wing root fairing; the wing was carefully merged into the fuselage, with root extensions at both leading and trailing edges. The meteorologists' cabin was under the wing where the fuselage width was {{convert|700|mm|in|abbr=on|1}}, with both side and roof windows. Both the pilot and observers entered via a detachable hood; cabin and cockpit were connected via a door. Below them were a side-by-side pair of fixed, semi-recessed landing wheels. The fuselage tapered to the tail, where a short, narrow fin carried a broad chord, triangular, blunt apexed balanced rudder that extended to the keel. Its mass balanced, all-moving tailplane was mounted on inverted V-form struts from its mid-span, forward underside to the lower fuselage, placing it above the fuselage with its leading edge just ahead of the fin.^[3]

After flying at the Wasserkuppe in 1932 with the aid of powerful tug aircraft, it was moved to Darmstadt to commence its intended meteorological observations. It was on view at a meteorological conference in Munich in 1934.^[3]

Specifications

|prime units?=met

|perfhide=
|max speed kmh=
|max speed mph=
|max speed kts=
|max speed note=
|stall speed kmh=
|stall speed mph=
|stall speed kts=
|stall speed note=
|never exceed speed kmh=
|never exceed speed mph=
|never exceed speed kts=
|never exceed speed note=
|endurance=
|ceiling m=
|ceiling ft=
|ceiling note=
|g limits=
|roll rate=
|glide ratio=
|sink rate ms=
|sink rate ftmin=
|sink rate note=
|lift to drag=
|wing loading kg/m2=16.8
|wing loading lb/sqft=
|wing loading note=
|more performance=
}}{{aircontent
|see also=
|related=
|similar aircraft=
|lists=
}}

References

1. ^¹²³{{cite journal |last= |first= |authorlink= |coauthors= |date=3 March 1933|title= A Two-Seater for Research|journal= The Sailplane|volume=4 |issue=4 |pages=41–2|url= http://scalesoaring.co.uk/VINTAGE/Documentation/OBS/OBS.html}}

[1]

5 : German sailplanes 1930–1939|High-wing aircraft|Gull-wing aircraft|Glider aircraft|Aircraft first flown in 1932