“Ethylene oxide”的意思、由来-开放百科全书

Ethylene oxide, called oxirane by IUPAC, is an organic compound with the formula {{chem|C|2|H|4|O}}. It is a cyclic ether and the simplest epoxide: a three-membered ring consisting of one oxygen atom and two carbon atoms. Ethylene oxide is a colorless and flammable gas with a faintly sweet odor. Because it is a strained ring, ethylene oxide easily participates in a number of addition reactions that result in ring-opening. Ethylene oxide is isomeric with acetaldehyde and with vinyl alcohol. Ethylene oxide is industrially produced by oxidation of ethylene in the presence of silver catalyst.

The reactivity that is responsible for many of ethylene oxide's hazards also make it useful. Although too dangerous for direct household use and generally unfamiliar to consumers, ethylene oxide is used for making many consumer products as well as non-consumer chemicals and intermediates. These products include detergents, thickeners, solvents, plastics, and various organic chemicals such as ethylene glycol, ethanolamines, simple and complex glycols, polyglycol ethers, and other compounds. Although it is a vital raw material with diverse applications, including the manufacture of products like polysorbate 20 and polyethylene glycol (PEG) that are often more effective and less toxic than alternative materials, ethylene oxide itself is a very hazardous substance. At room temperature it is a flammable, carcinogenic, mutagenic, irritating, and anaesthetic gas.^[20]

As a toxic gas that leaves no residue on items it contacts, ethylene oxide is a surface disinfectant that is widely used in hospitals and the medical equipment industry to replace steam in the sterilization of heat-sensitive tools and equipment, such as disposable plastic syringes.^[8] It is so flammable and extremely explosive that it is used as a main component of thermobaric weapons;^[22]^[23] therefore, it is commonly handled and shipped as a refrigerated liquid to control its hazardous nature.^[9]

History

Ethylene oxide was first reported in 1859 by the French chemist Charles-Adolphe Wurtz,^[10] who prepared it by treating 2-chloroethanol with potassium hydroxide:

Wurtz measured the boiling point of ethylene oxide as {{Convert|13.5|C|}}, slightly higher than the present value, and discovered the ability of ethylene oxide to react with acids and salts of metals.^[11] Wurtz mistakenly assumed that ethylene oxide has the properties of an organic base. This misconception persisted until 1896 when Georg Bredig found that ethylene oxide is not an electrolyte.^[11]^[12] That it differed from other ethers — particularly by its propensity to engage in addition reactions, which are typical of unsaturated compounds — had long been a matter of debate. The heterocyclic triangular structure of ethylene oxide was proposed by 1868 or earlier.^[13]

Wurtz's 1859 synthesis long remained the only method of preparing ethylene oxide, despite numerous attempts, including by Wurtz himself, to produce ethylene oxide directly from ethylene.^[14] Only in 1931 did French chemist Theodore Lefort develop a method of direct oxidation of ethylene in the presence of silver catalyst.^[15] Since 1940, almost all industrial production of ethylene oxide has relied on this process.^[16] Sterilization by ethylene oxide for the preservation of spices was patented in 1938 by the American chemist Lloyd Hall. Ethylene oxide achieved industrial importance during World War I as a precursor to both the coolant ethylene glycol and the chemical weapon mustard gas.

Molecular structure and properties

The epoxy cycle of ethylene oxide is an almost regular triangle with bond angles of about 60° and a significant angular strain corresponding to the energy of 105 kJ/mol.^[17]^[18] For comparison, in alcohols the C–O–H angle is about 110°; in ethers, the C–O–C angle is 120°. The moment of inertia about each of the principal axes are I_A = 32.921×10⁻⁴⁰ g·cm², I_B = 37.926×10⁻⁴⁰ g·cm² and I_C = 59.510×10⁻⁴⁰ g·cm².^[19]

The relative instability of the carbon-oxygen bonds in the molecule is revealed by the comparison in the table of the energy required to break two C–O bonds in the ethylene oxide or one C–O bond in ethanol and dimethyl ether:^[20]

This instability correlates with its high reactivity, explaining the ease of its ring-opening reactions (see Chemical properties).

Physical properties

Ethylene oxide is a colorless gas at {{Convert|25|C|}} and is a mobile liquid at {{Convert|0|C|}} – viscosity of liquid ethylene oxide at 0 °C is about 5.5 times lower than that of water. The gas has a characteristic sweet odor of ether, noticeable when its concentration in air exceeds 500{{nbsp}}ppm.^[21] Ethylene oxide is readily soluble in water, ethanol, diethyl ether and many organic solvents.^[22]

Between {{Convert|−91|and|10.5|C}}, vapor pressure p (in mmHg) varies with temperature (T in °C) as

Chemical properties

Ethylene oxide readily reacts with diverse compounds with opening of the ring. Its typical reactions are with nucleophiles which proceed via the S_N2 mechanism both in acidic (weak nucleophiles: water, alcohols) and alkaline media (strong nucleophiles: OH⁻, RO⁻, NH₃, RNH₂, RR'NH, etc.).^[18] The general reaction scheme is

Addition of water and alcohols

Aqueous solutions of ethylene oxide are rather stable and can exist for a long time without any noticeable chemical reaction, but adding a small amount of acid, such as strongly diluted sulfuric acid, immediately leads to the formation of ethylene glycol, even at room temperature:

The reaction also occurs in the gas phase, in the presence of a phosphoric acid salt as a catalyst.^[28]

The reaction is usually carried out at about {{Convert|60|C|}} with a large excess of water, in order to prevent the reaction of the formed ethylene glycol with ethylene oxide that would form di- and triethylene glycol:^[29]

Reactions with lower alcohols occur less actively than with water and require more severe conditions, such as heating to {{Convert|160|C|}} and pressurizing to {{Convert|3|MPa||abbr=on}} and adding an acid or alkali catalyst.

Reactions of ethylene oxide with fatty alcohols proceed in the presence of sodium metal, sodium hydroxide or boron trifluoride and are used for the synthesis of surfactants.^[28]

Addition of carboxylic acids and their derivatives

Reactions of ethylene oxide with carboxylic acids in the presence of a catalyst results in glycol mono- and diesters:

Addition of ethylene oxide to higher carboxylic acids is carried out at elevated temperatures (typically {{Convert|140-180|C|}}) and pressure ({{Convert|0.3-0.5|MPa||abbr=on}}) in an inert atmosphere, in presence of an alkaline catalyst (concentration 0.01–2%), such as hydroxide or carbonate of sodium or potassium.^[30] The carboxylate ion acts as nucleophile in the reaction:

Adding ammonia and amines

Ethylene oxide reacts with ammonia forming a mixture of mono-, di- and tri- ethanolamines. The reaction is stimulated by adding a small amount of water.

Dialkylamino ethanols can further react with ethylene oxide, forming amino polyethylene glycols:^[14]

Trimethylamine reacts with ethylene oxide in the presence of water, forming choline:^[31]

Aromatic primary and secondary amines also react with ethylene oxide, forming the corresponding arylamino alcohols.

Halide addition

Ethylene oxide readily reacts with aqueous solutions of hydrochloric, hydrobromic and hydroiodic acids to form halohydrins. The reaction occurs easier with the last two acids:

The reaction with these acids competes with the acid-catalyzed hydration of ethylene oxide; therefore, there is always a by-product of ethylene glycol with an admixture of diethylene glycol. For a cleaner product, the reaction is conducted in the gas phase or in an organic solvent.

Ethylene fluorohydrin is obtained differently, by boiling hydrogen fluoride with a 5–6% solution of ethylene oxide in diethyl ether. The ether normally has a water content of 1.5–2%; in absence of water, ethylene oxide polymerizes.^[32]

Halohydrins can also be obtained by passing ethylene oxide through aqueous solutions of metal halides:^[28]

Metalorganic addition

Interaction of ethylene oxide with organomagnesium compounds, which are Grignard reagents, can be regarded as nucleophilic substitution influenced by carbanion organometallic compounds. The final product of the reaction is a primary alcohol:

Similar mechanism is valid for other organometallic compounds, such as alkyl lithium:

Other addition reactions

Addition of hydrogen cyanide

Ethylene oxide easily reacts with the hydrogen cyanide forming ethylene cyanohydrin:

A slightly chilled (10–20 °C) aqueous solution of calcium cyanide can be used instead of HCN:^[33]

Addition of hydrogen sulfide and mercaptans

When reacting with the hydrogen sulfide, ethylene oxide forms 2-mercaptoethanol and thiodiglycol, and with alkylmercaptans it produces 2-alkyl mercaptoetanol:

The excess of ethylene oxide with an aqueous solution of hydrogen sulfide leads to the tris-(hydroxyethyl) sulfonyl hydroxide:

Addition of nitrous and nitric acids

Reaction of ethylene oxide with aqueous solutions of barium nitrite, calcium nitrite, magnesium nitrite, zinc nitrite or sodium nitrite leads to the formation of 2-nitroethanol:^[34]

Reaction with compounds containing active methylene groups

In the presence of alkoxides, reactions of ethylene oxide with compounds containing active methylene group leads to the formation of butyrolactones:^[36]

Alkylation of aromatic compounds

Ethylene oxide enters into the Friedel–Crafts reaction with benzene to form phenethyl alcohol:

Synthesis of crown ethers

A series of polynomial heterocyclic compounds, known as crown ethers, can be synthesized with ethylene oxide. One method is the cationic cyclopolymerization of ethylene oxide, limiting the size of the formed cycle:^[38]

To suppress the formation of other linear polymers the reaction is carried out in a highly dilute solution.^[38]

Reaction of ethylene oxide with sulfur dioxide in the presence of caesium salts leads to the formation of an 11-membered heterocyclic compound which has the complexing properties of crown ethers:^[39]

Isomerization

When heated to about {{Convert|400|C||sigfig=2}}, or to {{Convert|150–300|C||sigfig=2}} in the presence of a catalyst (Al₂O₃, H₃PO₄, etc.), ethylene oxide isomerizes into acetaldehyde:^[40]

The radical mechanism was proposed to explain this reaction in the gas phase; it comprises the following stages:^[41]

In reaction ({{EquationNote|3}}), M refers to the wall of the reaction vessel or to a heterogeneous catalyst.

The moiety CH₃CHO* represents a short-lived (lifetime of 10^−8.5 seconds), activated molecule of acetaldehyde. Its excess energy is about 355.6 kJ/mol, which exceeds by 29.3 kJ/mol the binding energy of the C-C bond in acetaldehyde.^[41]

In absence of a catalyst, the thermal isomerization of ethylene oxide is never selective and apart from acetaldehyde yields significant amount of by-products (see section Thermal decomposition).^[66]

Reduction reaction

Ethylene oxide can be hydrogenated into ethanol in the presence of a catalyst, such as nickel, platinum, palladium,^[66] boranes, lithium aluminium hydride and some other hydrides.^[42]

Conversely, with some other catalysts, ethylene oxide may be reduced by hydrogen to ethylene with the yield up to 70%. The reduction catalysts include mixtures of zinc dust and acetic acid, of lithium aluminium hydride with titanium trichloride (the reducing agent is actually titanium dichloride, formed by the reaction between LiAlH₄ and TiCl₃) and of iron(III) chloride with butyllithium in tetrahydrofuran.^[42]

Oxidation

Ethylene oxide can further be oxidized, depending on the conditions, to glycolic acid or carbon dioxide:

Deep gas-phase reactor oxidation of ethylene oxide at {{Convert|800-1000|K|}} and a pressure of {{Convert|0.1–1|MPa||abbr=on}} yields a complex mixture of products containing O₂, H₂, CO, CO₂, CH₄, C₂H₂, C₂H₄, C₂H₆, C₃H₆, C₃H₈ and CH₃CHO.^[43]

Dimerization

The dimerization reaction is unselective. By-products include acetaldehyde (due to isomerization). The selectivity and speed of dimerization can be increased by adding a catalyst, such as platinum, platinum-palladium, or iodine with sulfolane. 2-methyl-1,3-dioxolane is formed as a side product in the last case.^[44]

Polymerization

Liquid ethylene oxide can form polyethylene glycols. The polymerization can proceed via radical and ionic mechanisms, but only the latter has a wide practical application.^[45] Cationic polymerization of ethylene oxide is assisted by protic acids (HClO₄, HCl), Lewis acids (SnCl₄, BF₃, etc.), organometallic compounds, or more complex reagents:^[45]

The reaction mechanism is as follows.^[46] At the first stage, the catalyst (MX_m) is initiated by alkyl-or acylhalogen or by compounds with active hydrogen atoms, usually water, alcohol or glycol:

The resulting active complex reacts with ethylene oxide via the S_N2 mechanism:

Thermal decomposition

Ethylene oxide is relatively stable to heating – in the absence of a catalyst, it does not dissociate up to {{Convert|300|C|}}, and only above {{Convert|570|C|}} there is a major exothermic decomposition, which proceeds through the radical mechanism.^[47] The first stage involves isomerization, however high temperature accelerates the radical processes. They result in a gas mixture containing acetaldehyde, ethane, ethyl, methane, hydrogen, carbon dioxide, ketene and formaldehyde.^[48] High-temperature pyrolysis ({{Convert|830–1200|K|}}) at elevated pressure in an inert atmosphere leads to a more complex composition of the gas mixture, which also contains acetylene and propane.^[49] Contrary to the isomerization, initiation of the chain occurs mainly as follows:^[49]

When carrying the thermal decomposition of ethylene oxide in the presence of transition metal compounds as catalysts, it is possible not only to reduce its temperature, but also to have ethyl as the main product, that is to reverse the ethylene oxide synthesis reaction.

Other reactions

Reaction of phosphorus pentachloride with ethylene oxide produces ethylene dichloride:^[28]

Other dichloro derivatives of ethylene oxide can be obtained by combined action of sulfuryl chloride (SOCl₂) and pyridine and of triphenylphosphine and carbon tetrachloride.^[51]

The reaction product of ethylene oxide with acyl chlorides in the presence of sodium iodide is a complex iodoethyl ester:^[51]

Heating ethylene oxide to 100 °C with carbon dioxide, in a non-polar solvent in the presence of bis-(triphenylphosphine)-nickel(0) results in ethylene carbonate:^[52]

In industry, a similar reaction is carried out at high pressure and temperature in the presence of quaternary ammonium or phosphonium salts as a catalyst.^[53]

Reaction of ethylene oxide with formaldehyde at 80–150 °C in the presence of a catalyst leads to the formation of 1,3-dioxolane:^[54]

Substituting formaldehyde by other aldehydes or ketones results in a 2-substituted 1,3-dioxolane (yield: 70–85%, catalyst: tetraethylammonium bromide).^[54]

Catalytic hydroformylation of ethylene oxide gives hydroxypropanal which can be hydrogenated to propane-1,3-diol:^[55]

Laboratory synthesis

Dehydrochlorination of ethylene and its derivatives

Dehydrochlorination of 2-chloroethanol, developed by Wurtz back in 1859, remains a common laboratory route to ethylene oxide:

The reaction is carried out at elevated temperature, and beside sodium hydroxide or potassium hydroxide, calcium hydroxide, barium hydroxide, magnesium hydroxide or carbonates of alkali or alkaline earth metals can be used.^[56]

With a high yield (90%) ethylene oxide can be produced by treating calcium oxide with ethyl hypochlorite; substituting calcium by other alkaline earth metals reduces the reaction yield:^[57]

Direct oxidation of ethylene by peroxy acids

Ethylene can be directly oxidized into ethylene oxide using peroxy acids, for example, peroxybenzoic or meta-chloro-peroxybenzoic acid:^[58]

Oxidation by peroxy acids is efficient for higher alkenes, but not for ethylene. The above reaction is slow and has low yield, therefore it is not used in the industry.^[57]

Other preparative methods

Other synthesis methods include^[57] reaction of diiodo ethane with silver oxide:

and decomposition of ethylene carbonate at {{Convert|200–210|C|}} in the presence of hexachloroethane:

Industrial synthesis

History

Commercial production of ethylene oxide dates back to 1914 when BASF built the first factory which used the chlorohydrin process (reaction of ethylene chlorohydrin with calcium hydroxide). The chlorohydrin process was unattractive for several reasons, including low efficiency and loss of valuable chlorine into calcium chloride.^[59] More efficient direct oxidation of ethylene by air was invented by Lefort in 1931 and in 1937 Union Carbide opened the first plant using this process. It was further improved in 1958 by Shell Oil Co. by replacing air with oxygen and using elevated temperature of {{Convert|200–300|C||sigfig=2}} and pressure ({{Convert|1–3|MPa||abbr=on}}).^[98] This more efficient routine accounted for about half of ethylene oxide production in the 1950s in the US, and after 1975 it completely replaced the previous methods.^[60]

The production of ethylene oxide accounts for approximately 11% of worldwide ethylene demand.^[61]

Chlorohydrin process of production of ethylene oxide

Although the chlorohydrin process is almost entirely superseded in the industry by the direct oxidation of ethylene, the knowledge of this method is still important for educational reasons and because it is still used in the production of propylene oxide.^[62] The process consists of three major steps: synthesis of ethylene chlorohydrin, dehydrochlorination of ethylene chlorohydrin to ethylene oxide and purification of ethylene oxide. Those steps are carried continuously. In the first column, hypochlorination of ethylene is carried out as follows:^[63]

To suppress the conversion of ethylene into the ethylene dichloride (the last reaction), the concentration of ethylene is maintained at about 4–6%, and the solution is heated by steam to the boiling point.^[63]

Next, aqueous solution of ethylene chlorohydrin enters the second column, where it reacts with a 30% solution of calcium hydroxide at {{Convert|100|C|}}:^[63]

The produced ethylene oxide is purified by rectification. The chlorohydrin process allows to reach 95% conversion of ethylene chlorohydrin. The yield of ethylene oxide is about 80% of the theoretical value; for {{Convert|1|t|}} of ethylene oxide, about {{Convert|200|kg||abbr=on}} of ethylene dichloride is produced.^[63] But, the major drawbacks of this process are high chlorine consumption and effluent load. This process is now obsolete.

Direct oxidation of ethylene

Usage in global industry

Direct oxidation of ethylene was patented by Lefort in 1931. This method was repeatedly modified for industrial use, and at least four major variations are known. They all use oxidation by oxygen or air and a silver-based catalyst, but differ in the technological details and hardware implementations.^[64]

A similar production method was developed by Scientific Design Co., but it received wider use because of the licensing system – it accounts for 25% of the world's production and for 75% of world's licensed production of ethylene oxide.^[65]^[66] A proprietary variation of this method is used by Japan Catalytic Chemical Co., which adapted synthesis of both ethylene oxide and ethylene glycol in a single industrial complex.

A different modification was developed Shell International Chemicals BV. Their method is rather flexible with regard to the specific requirements of specific industries; it is characterized by high selectivity with respect to the ethylene oxide product and long lifetime of the catalyst (3 years). It accounts for about 40% of global production.^[65]

Older factories typically use air for oxidation whereas newer plants and processes, such as METEOR and Japan Catalytic, favor oxygen.^[67]

Chemistry and kinetics of the direct oxidation process

However, significant yield of carbon dioxide and water is observed in practice, which can be explained by the complete oxidation of ethylene or ethylene oxide:

The process of heterogeneous catalytic oxidation of ethylene was studied by P. A. Kilty and W. M. H. Sachtler, who suggested the following mechanism:^[68]

Here (ads) refers to particles adsorbed on the catalyst surface and (adj) to particles of silver, directly adjacent to the oxygen atoms. In this process, 1,2-dichloroethane, vinyl chloride are used as inhibitors so as to prevent further oxidation of ethylene oxide to CO₂ and H₂O. Here, the chemisorbed chlorine hinders dissociative chemisorption of atomic oxygen.

and the maximum degree of conversion of ethylene to ethylene oxide is 6/7 or 85.7%.^[68]

The catalyst for the reaction is metallic silver deposited on various matrixes, including pumice, silica gel, various silicates and aluminosilicates, alumina and silicon carbide, and activated by certain additives (antimony, bismuth, barium peroxide, etc.).^[69] The process temperature was optimized as {{Convert|220–280|C||sigfig=2}}. Lower temperatures reduce the activity of the catalyst, and higher temperatures promote the complete oxidation of ethylene thereby reducing the yield of ethylene oxide. Elevated pressure of {{Convert|1-3|MPa||abbr=on}} increases the productivity of the catalyst and facilitates absorption of ethylene oxide from the reacting gases.^[69]

Whereas oxidation by air is still being used, oxygen (> 95% purity) is preferred for several reasons, such as higher molar yield of ethylene oxide (75–82% for oxygen vs. 63–75% for air), higher reaction rate (no gas dilution) and no need of separating nitrogen in the reaction products.^[14]^[70]

Process overview

The production of ethylene oxide on a commercial scale is attained with the unification of the following unit processes:

Main Reactor: The main reactor consists of thousands of catalyst tubes in bundles. These tubes are generally {{Convert|6|to|15|m|abbr=on|round=5}} long with an inner diameter of {{Convert|20|to|50|mm|abbr=on|1}}. The catalyst packed in these tubes is in the form of spheres or rings of diameter {{Convert|3|to|10|mm|abbr=on}}. The operating conditions of {{Convert|200-300|C||sigfig=2}} with a pressure of {{Convert|1-3|MPa||abbr=on}} prevail in the reactor. To maintain this temperature, the cooling system of the reactor plays a vital role. With the aging of the catalyst, its selectivity decreases and it produces more exothermic side products of CO₂.

Ethylene oxide scrubber: After the gaseous stream from the main reactor, containing ethylene oxide (1–2%) and CO₂ (5%), is cooled, it is then passed to the ethylene oxide scrubber. Here, water is used as the scrubbing media which scrubs away majority of ethylene oxide along with some amounts of CO₂, N₂, CH₂=CH₂, CH₄ and aldehydes (introduced by the recycle stream). Also, a small proportion of the gas leaving the ethylene oxide scrubber (0.1–0.2%) is removed continuously (combusted) to prevent the buildup of inert compounds (N₂, Ar, and C₂H₆), which are introduced as impurities with the reactants.

Ethylene oxide de-sorber: The aqueous stream resulting from the above scrubbing process is then sent to the ethylene oxide de-sorber. Here, ethylene oxide is obtained as the overhead product, whereas the bottom product obtained is known as the glycol bleed. When ethylene oxide is scrubbed from the recycle gas with an aqueous solution, ethylene glycols (viz. mono-ethylene glycol, di-ethylene glycol and other poly-ethylene glycols) get unavoidably produced. Thus, in-order to prevent them from building up in the system, they are continuously bled off.

Stripping and distillation column: Here, the ethylene oxide stream is stripped off its low boiling components and then distilled in-order to separate it into water and ethylene oxide.

CO₂ scrubber: The recycle stream obtained from the ethylene oxide scrubber is compressed and a side-stream is fed to the CO₂ scrubber. Here, CO₂ gets dissolved into the hot aqueous solution of potassium carbonate (i.e., the scrubbing media). The dissolution of CO₂ is not only a physical phenomenon, but a chemical phenomenon as well, for, the CO₂ reacts with potassium carbonate to produce potassium hydrogen carbonate.

CO₂ de-scrubber: The above potassium carbonate solution (enriched with CO₂) is then sent to the CO₂ de-scrubber where CO₂ is de-scrubbed by stepwise (usually two steps) flashing. The first step is done to remove the hydrocarbon gases, and the second step is employed to strip off CO₂.

World production of ethylene oxide

The world production of ethylene oxide was {{Convert|20|e6t|e6ST e6LT|abbr=off}} in 2009,^[118] {{Convert|19|e6t|e6ST e6LT|abbr=off}} in 2008 and {{Convert|18|e6t|e6ST e6LT|abbr=off}} in 2007.^[71] This places ethylene oxide 14th most produced organic chemical, whereas the most produced one was ethylene with {{Convert|113|e6t|e6ST e6LT|abbr=off}}.^[72] SRI Consulting forecasted the growth of consumption of ethylene oxide of 4.4% per year during 2008–2013 and 3% from 2013 to 2018.^[71]

In 2004, the global production of ethylene oxide by region was as follows:^[122]

The world's largest producers of ethylene oxide are Dow Chemical Company ({{Convert|3-3.5|e6t|e6ST e6LT|abbr=off}} in 2006^[73]), Saudi Basic Industries ({{Convert|2000-2500|t|ST LT}} in 2006^[73]), Royal Dutch Shell ({{Convert|1.328|e6t|e6ST e6LT|abbr=off}} in 2008–2009^[74]^[75]^[76]^[77]), BASF ({{Convert|1.175|e6t|e6ST e6LT|abbr=off}} in 2008–2009^[78]), China Petrochemical Corporation (~{{Convert|1|e6t|e6ST e6LT|abbr=off}} in 2006^[73]), Formosa Plastics (~{{Convert|1|e6t|e6ST e6LT|abbr=off}} in 2006^[73]) and Ineos ({{Convert|0.92|e6t|e6ST e6LT|abbr=off}} in 2008–2009).^[79]

Applications

Ethylene oxide is one of the most important raw materials used in large-scale chemical production. Most ethylene oxide is used for synthesis of ethylene glycols, including diethylene glycol and triethylene glycol, that accounts for up to 75% of global consumption. Other important products include ethylene glycol ethers, ethanolamines and ethoxylates. Among glycols, ethylene glycol is used as antifreeze, in the production of polyester and polyethylene terephthalate (PET – raw material for plastic bottles), liquid coolants and solvents.

Polyethyleneglycols are used in perfumes, cosmetics, pharmaceuticals, lubricants, paint thinners and plasticizers. Ethylene glycol ethers are part of brake fluids, detergents, solvents, lacquers and paints. Other products of ethylene oxide. Ethanolamines are used in the manufacture of soap and detergents and for purification of natural gas. Ethoxylates are reaction products of ethylene oxide with higher alcohols, acids or amines. They are used in the manufacture of detergents, surfactants, emulsifiers and dispersants.^[80]

Whereas synthesis of ethylene glycols is the major application of ethylene oxide, its percentage varies greatly depending on the region: from 44% in the Western Europe, 63% in Japan and 73% in North America to 90% in the rest of Asia and 99% in Africa.^[81]

Production of ethylene glycol

Ethylene glycol is industrially produced by non-catalytic hydration of ethylene oxide at a temperature of {{Convert|200|C|}} and a pressure of {{Convert|1.5-2|MPa||abbr=on}}:^[82]

By-products of the reaction are diethylene glycol, triethylene glycol and polyglycols with the total of about 10%, which are separated from the ethylene glycol by distillation at reduced pressure.^[83]

Another synthesis method is the reaction of ethylene oxide and CO₂ (temperature {{Convert|80–120|C|}} and pressure of {{Convert|5.2|MPa||abbr=on}}) yielding ethylene carbonate and its subsequent hydrolysis with decarboxylation:^[82]

Modern technologies of production of ethylene glycol include the following.^[84] Shell OMEGA technology (Only Mono-Ethylene Glycol Advantage) is a two-step synthesis of ethylene carbonate using a phosphonium halide as a catalyst. The glycol yield is 99–99.5%, with other glycols practically absent. The main advantage of the process is production of pure ethylene glycol without the need for further purification. The first commercial plant which uses this method was opened in 2008 in South Korea.^[85] Dow METEOR (Most Effective Technology for Ethylene Oxide Reactions) is an integrated technology for producing ethylene oxide and its subsequent hydrolysis into ethylene glycol. The glycol yield is 90–93%. The main advantage of the process is relative simplicity, using fewer stages and less equipment.

Conversion to ethylene glycol is also the means by which waste ethylene oxide is scrubbed before venting to the environment. Typically the EtO is passed over a matrix containing either sulfuric acid or potassium permanganate.{{cn|date=August 2018}}

Production of glycol ethers

The major industrial esters of mono-, di- and triethylene glycols are methyl, ethyl and normal butyl ethers, as well as their acetates and phthalates. The synthesis involves reaction of the appropriate alcohol with ethylene oxide:^[86]

The reaction of monoesters with an acid or its anhydride leads to the formation of the esters:

Production of ethanolamines

In the industry, ethanolamines (mono-, di- and triethanolamines) are produced by reacting ammonia and ethylene oxide in anhydrous medium at a temperature of {{Convert|40-70|C||-1}} and pressure of {{Convert|1.5-3.5|MPa||abbr=on}}{{nbsp}}MPa:^[87]

All three ethanolamines are produced in the process, while ammonia and part of methylamine are recycled. The final products are separated by vacuum distillation. Hydroxyalkylamines are produced in a similar process:

Monosubstituted products are formed by reacting a large excess of amine with ethylene oxide in presence of water and at a temperature below {{Convert|100|C|}}. Disubstituted products are obtained with a small excess of ethylene oxide, at a temperature of {{Convert|120–140|C||-1}} and a pressure of {{Convert|0.3-0.5|MPa||abbr=on|round=5}}.^[88]^[89]

Production of ethoxylates

Industrial production of ethoxylates is realized by a direct reaction of higher alcohols, acids or amines with ethylene oxide in the presence of an alkaline catalyst at a temperature of {{Convert|120–180|C||-1}}. Modern plants producing ethoxylates are usually based on the BUSS LOOP reactors technology,^[90] which is based on a three-stage continuous process. In the first stage, the initiator or catalyst of the reaction and the feedstock are fed into the container, where they are mixed, heated and vacuum dried. Then reaction is carried out in a special insulated reactor in an inert atmosphere (nitrogen) to prevent a possible explosion of ethylene oxide. Finally, the reaction mixture is neutralized, degassed and purified.^[91]

Production of acrylonitrile

Currently, most acrylonitrile (90% in 2008) is produced by the SOHIO method, which is based on the catalytic oxidation of propylene in the presence of ammonia and bismuth phosphomolybdate. However, until 1960 a key production process was addition of hydrogen cyanide to ethylene oxide, followed by dehydration of the resulting cyanohydrin:^[92]

Addition of hydrocyanic acid to ethylene oxide is carried out in the presence of a catalyst (sodium hydroxide and diethylamine), and dehydration of cyanohydrin occurs in the gas phase upon the catalytic action of aluminium oxide.^[94]

Non-industrial uses

The direct use of ethylene oxide accounts for only 0.05% (2004 data) of its global production.^[122] Ethylene oxide is used as a sterilizing agent, disinfecting agent and fumigant as a mixture with carbon dioxide (8.5–80% of ethylene oxide), nitrogen or dichlorodifluoromethane (12% ethylene oxide). It is applied for gas-phase sterilization of medical equipment and instruments, packaging materials and clothing, surgical and scientific equipment;^[95] for processing of storage facilities (tobacco, packages of grain, sacks of rice, etc.), clothing, furs and valuable documents.^[96]

Healthcare sterilant

Ethylene oxide is one of the most commonly used sterilization methods in the healthcare industry because of its non-damaging effects for delicate instruments and devices that require sterilization, and for its wide range of material compatibility.^[97] It is used for instruments that cannot tolerate heat, moisture or abrasive chemicals, such as electronics, optical equipment, paper, rubber and plastics.^[98] It was developed in the 1940s as a sterilant by the US military, and its use as a medical sterilant dates to the late 1950s, when the McDonald process was patented for medical devices.^[99] The Anprolene system was patented in the 1960s^[100] by Andersen Products,^[101] and it remains the most commonly used system in several niche markets, notably the veterinary market and some international markets.^[102] It relies on the use of a flexible sterilization chamber and an EtO cartridge for small volume sterilization, and where environmental and/or portability considerations dictate the use of a low dose. It is therefore referred to as the "flexible chamber sterilization" method, or the "gas diffusion sterilization" method.

In the United States, the operation of EtO sterilization is overseen by the EPA through the National Emission Standard for Hazardous Air Pollutants.^[103]

Niche uses

Ethylene oxide is used as an accelerator of maturation of tobacco leaves and fungicide.^[96] Ethylene oxide is also used as a main component of thermobaric weapons (fuel-air explosives).^[104]^[105]^[106]

Ethylene is used in the synthesis in 2-butoxyethanol, which is a solvent used in many products.^[107]

Identification of ethylene oxide

An inexpensive test for ethylene oxide exploits its precipitation of solid hydroxides of metals when it is passed through aqueous solutions of their salts:

Similarly, ethylene oxide is detected by the bright pink color of the indicator when passing air through aqueous solutions of some salts of sodium or potassium (chlorides, iodides, thiosulfates, etc.) with the addition of phenolphthalein:^[108]

Other methods of ethylene oxide detection are^[108] color reactions with pyridine derivatives and hydrolysis of ethylene glycol with periodic acid. The produced iodic acid is detected with silver nitrate.

Fire and explosion hazards

Ethylene oxide is extremely flammable, and its mixtures with air are explosive. When heated it may rapidly expand, causing fire and explosion.^[109] A number of industrial accidents have been attributed to ethylene oxide explosion.^[110]^[111]^[112]

The autoignition temperature is {{Convert|429|C|}}, decomposition temperature of {{Convert|571|C|}} at {{Convert|101.3|kPa||abbr=on}}, minimum inflammable content in the air is 2.7%,^[113] and maximum limit is 100%. The NFPA rating is NFPA 704.^[114] Ethylene oxide in presence of water can hydrolyze to ethylene glycol and form poly ethylene oxide which then eventually gets oxidized by air and leads to hotspots that can trigger to explosive decomposition.

Fires caused by ethylene oxide are extinguished by traditional media, including foam, carbon dioxide or water. Suppression of this activity can be done by blanketing with an inert gas until total pressure reaches non explosive range. Extinguishing of burning ethylene oxide is complicated by that it can continue burning in an inert atmosphere and in water solutions. Fire suppression is reached only upon dilution with water above 22:1.^[115]

Physiological effects

Effect on microorganisms

Exposure to ethylene oxide gas causes alkylation to microorganisms at a nuclear level.^[116] The disinfectant effect of ethylene oxide is similar to that of sterilization by heat, but because of limited penetration, it affects only the surface. ETO sterilization can take up to 12 hours due to its slow action upon microorganisms, and lengthy processing and aeration time.^[117]

Effects on humans and animals

Ethylene oxide is an alkylating agent; it has irritating, sensitizing and narcotic effects.^[118] Chronic exposure to ethylene oxide is also mutagenic. The International Agency for Research on Cancer classifies ethylene oxide into group 1, meaning it is a proven carcinogen.^[119]^[120] Ethylene oxide is classified as a class 2 carcinogen by the German MAK commission and as a class A2 carcinogen by the ACGIH. A 2003 study of 7,576 women exposed while at work in commercial sterilization facilities in the US suggests ethylene oxide is associated with breast cancer incidence.^[121] A 2004 follow up study analyzing 18,235 men and women workers exposed to ethylene oxide from 1987 to 1998 concluded "There was little evidence of any excess cancer mortality for the cohort as a whole, with the exception of bone cancer based on small numbers. Positive exposure-response trends for lymphoid tumors were found for males only. Reasons for the sex specificity of this effect are not known. There was also some evidence of a positive exposure-response for breast cancer mortality."^[122] An increased incidence of brain tumors and mononuclear cell leukemia was found in rats that had inhaled ethylene oxide at concentrations of {{Convert|10|,|33|or|abbr=on|100|mL/m3}} over a period of two years.^[123] An increased incidence of peritoneal mesotheliomas was also observed in the animals exposed to concentrations of {{Convert|33|and|100|mL/m3|abbr=on|4}}. Results of human epidemiological studies on workers exposed to ethylene oxide differ. There is evidence from both human and animal studies that inhalation exposure to ethylene oxide can result in a wide range of carcinogenic effects.

Ethylene oxide is toxic by inhalation, with a US OSHA permissible exposure limit calculated as a TWA (time weighted average) over 8 hours of 1{{nbsp}}ppm, and a short term exposure limit (excursion limit) calculated as a TWA over 15 minutes of 5{{nbsp}}ppm.^[184] At concentrations in the air about 200 parts per million, ethylene oxide irritates mucous membranes of the nose and throat; higher contents cause damage to the trachea and bronchi, progressing into the partial collapse of the lungs. High concentrations can cause pulmonary edema and damage the cardiovascular system; the damaging effect of ethylene oxide may occur only after 72 hours after exposure.^[21] The maximum content of ethylene oxide in the air according to the US standards (ACGIH) is {{Convert|1.8|mg/m3||abbr=on}}.^[124] NIOSH has determined that the Immediately Dangerous to Life and Health level (IDLH) is 800 ppm.^[125]

Because the odor threshold for ethylene oxide varies between 250 and 700 ppm, the gas is already at toxic concentrations when it can be smelled. Even then, the odor of ethylene oxide is sweet, aromatic, and can easily be mistaken for the pleasant aroma of diethyl ether, a common laboratory solvent of very low toxicity. In view of these insidious warning properties, continuous electrochemical monitors are standard practice, and it is forbidden to use ethylene oxide to fumigate building interiors in the EU and some other jurisdictions.^[126]

Ethylene oxide causes acute poisoning, accompanied by a variety of symptoms.^[118] Central nervous system effects are frequently associated with human exposure to ethylene oxide in occupational settings. Headache, nausea, and vomiting have been reported.{{clarify|date=February 2017|reason="50 years of reports and/or 50 years of symptoms post-exposure?"}} Peripheral neuropathy, impaired hand-eye coordination and memory loss have been reported in more recent case studies of chronically-exposed workers at estimated average exposure levels as low as 3 ppm (with possible short-term peaks as high as 700{{nbsp}}ppm).^[123] The metabolism of ethylene oxide is not completely known. Data from animal studies indicate two possible pathways for the metabolism of ethylene oxide: hydrolysis to ethylene glycol and glutathione conjugation to form mercapturic acid and meththio-metabolites.

Ethylene oxide easily penetrates through ordinary clothing and footwear, causing skin irritation and dermatitis with the formation of blisters, fever and leukocytosis.^[118]

Global demand

Global EO demand has expanded from {{Convert|16.6|Mt|e6ST e6LT|lk=in|abbr=unit}} in 2004 to {{Convert|20|Mt|e6ST e6LT|abbr=unit}} in 2009, while demand for refined EO expanded from {{Convert|4.64|Mt|e6ST e6LT|abbr=unit}} in 2004 to {{Convert|5.6|Mt|e6ST e6LT|abbr=unit}} in 2008. In 2009, demand is estimated to have declined to about {{Convert|5.2|Mt|e6ST e6LT|abbr=unit}}. Total EO demand registered a growth rate of 5.6% per annum during the period 2005 to 2009 and is projected to grow at 5.7% per annum during 2009 to 2013.^[129]

References

1. ^[https://pubchem.ncbi.nlm.nih.gov/summary/summary.cgi?cid=6354&loc=ec_rcs Oxirane | C2H4O – PubChem]. Pubchem.ncbi.nlm.nih.gov. Retrieved on 2017-05-08.
2. ^¹²³⁴Haynes, p. 3.430
3. ^Haynes, p. 3.576
4. ^¹²³Haynes, p. 5.22
5. ^¹²Haynes, p. 15.20
6. ^¹²³{{PGCH|0275}}
7. ^{{IDLH|75218|Ethylene oxide}}
8. ^{{cite book|url=https://books.google.com/books?id=oJy5wdzi0yUC&pg=PA309|page=309|title=Encyclopedia of Chemical Processing and Design|volume=20|author1=McKetta, John J. |author2=Cunningham, William A. |publisher=CRC Press|year=1984|isbn=0-8247-2470-4}}
9. ^¹Rebsdat, Siegfried and Mayer, Dieter (2005) "Ethylene Oxide" in Ullmann's Encyclopedia of Industrial Chemistry. Wiley-VCH, Weinheim. {{DOI|10.1002/14356007.a10_117}}.
10. ^{{cite journal|author=Wurtz, A.|journal= Comptes rendus|volume= 48|pages= 101–105 |year=1859| title= Sur l'oxyde d'éthylène| url= http://gallica.bnf.fr/ark:/12148/bpt6k30054/f101.image}}
11. ^¹{{cite book| chapter = Part I. Structure and properties of ethylene oxide. Features of the reactivity of ethylene oxide and the structure of its molecules| title = Ethylene oxide|editor1=Zimakov, P.V. |editor2=Dyment, O. H. | publisher = Khimiya| year = 1967| pages = 15–17}}
12. ^{{cite journal|author=Bredig, G.|author2= Usoff, A. |year=1896|url=https://books.google.com/books?id=0cPmAAAAMAAJ&pg=PA116 |title=Ist Acetylen ein Elektrolyt?|trans-title=Is acetylene an electrolyte?|journal=Zeitschrift für Elektrochemie|volume=3|pages=116–117}}
13. ^Eugen F. von Gorup-Besanez, ed., Lehrbuch der organischen Chemie für den Unterricht auf Universitäten … [Textbook of Organic Chemistry for Instruction at Universities … ], 3rd ed. (Braunschweig, Germany: Friedrich Vieweg und Sohn, 1868), vol. 2, [https://books.google.com/books?id=UJyCAAAAIAAJ&pg=PA286 p. 286].
See also [https://books.google.com/books?id=oc5Qth0MKE8C&pg=PA253 p. 253] of the 1876 edition: Eugen F. von Gorup-Besanez, ed., Lehrbuch der organischen Chemie für den Unterricht auf Universitäten …, 5th ed. (Braunschweig, Germany: Friedrich Vieweg und Sohn, 1876), vol. 2.
14. ^¹²³⁴{{cite book| chapter = Ethylene Oxide| title = Kirk-Othmer Encyclopedia of Chemical Technology. Elastomers, synthetic to Expert Systems| edition = 4| location = New York| publisher = John Wiley & Sons| year = 1994| volume = 9| pages = 450–466}}
15. ^Lefort, T.E. (23 April 1935) "Process for the production of ethylene oxide". {{US Patent|1998878}}
16. ^{{cite journal|title= Manufacture and Uses of Ethylene Oxide and Ethylene Glycol| author= McClellan, P. P. | journal= Ind. Eng. Chem.|year= 1950| volume= 42|pages= 2402–2407| doi= 10.1021/ie50492a013|issue= 12}}
17. ^{{cite book| chapter= Voltage molecules| title = Chemical Encyclopedia| editor = Knunyants, I. L.| publisher = "Soviet encyclopedia"| year = 1988| volume = 3| pages = 330–334}}
18. ^¹{{cite book|author = Traven VF| title = Organic chemistry: textbook for schools| editor = VFTraven| publisher = ECC "Academkniga"| year = 2004| volume = 2| pages = 102–106| isbn = 5-94628-172-0}}
19. ^{{cite journal| author = Cunningham G. L.|author2= Levan W. I.|author3= Gwinn W. D.| title = The Rotational Spectrum of Ethylene Oxide| doi=10.1103/PhysRev.74.1537| journal = Phys. Rev.| year = 1948| volume = 74| page = 1537| issue = 10| bibcode= 1948PhRv...74.1537C}}
20. ^{{cite book| title = Energy of chemical bonds. Ionization potentials and electron affinity| editor =Kondrat'ev, VN| publisher = Nauka| year = 1974| pages = 77–78}}
21. ^¹{{cite web| url = http://www.atsdr.cdc.gov/MHMI/mmg137.html| title = Medical Management Guidelines for Ethylene Oxide| work = Medical Management Guidelines (MMGs)| publisher = Agency for Toxic Substances and Disease Registry| accessdate = 29 September 2009}}
22. ^{{cite web| url = http://dic.academic.ru/dic.nsf/bse/154711/Этилена| title = Этилена окись (Ethylene oxide)| publisher = Great Soviet Encyclopedia| accessdate = 25 September 2009| language =Russian}}
23. ^{{cite web | date = 1 April 2009 | url= http://chemanalytica.com/book/novyy_spravochnik_khimika_i_tekhnologa/12_obshchie_svedeniya/6084 | title = Термодинамические показатели органических соединений | publisher = ChemAnalitica.com | accessdate = 21 September 2009}}
24. ^{{cite web| date = 1 April 2009| url = http://chemanalytica.com/book/novyy_spravochnik_khimika_i_tekhnologa/12_obshchie_svedeniya/6118| title = Surface tension of liquefied gas at the border with its own steam| publisher = ChemAnalitica.com| accessdate = 21 September 2009}}
25. ^{{cite web| date = 1 April 2009| url = http://chemanalytica.com/book/novyy_spravochnik_khimika_i_tekhnologa/12_obshchie_svedeniya/6061| title = Boiling point or sublimation (°C) organic matter in the vapor pressure above 101.3 kPa| publisher = ChemAnalitica.com| accessdate = 21 September 2009}}
26. ^{{cite web| date = 1 April 2009| url = http://chemanalytica.com/book/novyy_spravochnik_khimika_i_tekhnologa/12_obshchie_svedeniya/6112| title = Viscosity of organic compounds| publisher = ChemAnalitica.com| accessdate = 21 September 2009}}
27. ^{{cite web| date = 1 April 2009| url = http://chemanalytica.com/book/novyy_spravochnik_khimika_i_tekhnologa/12_obshchie_svedeniya/6063| title = Vapor pressure of organic compounds| publisher = ChemAnalitica.com| accessdate = 21 September 2009}}
28. ^¹²³⁴{{cite book| chapter= Chapter III. Review of the individual reactions of ethylene oxide| title = Ethylene oxide|editor1=Zimakov, P.V. |editor2=Dyment, O. H. | location = M.| publisher = Khimiya| year = 1967| pages = 90–120}}
29. ^{{cite web| url = http://www.chemguide.co.uk/organicprops/alkenes/epoxyethane.html| title = Epoxyethane (Ethylene Oxide)| work = Alkenes menu| publisher = Chemguide| accessdate = 5 October 2009}}
30. ^{{cite book| title = Nonionic surfactants: organic chemistry|editor1=van Os |editor2=N. M. | publisher = CRC Press| year = 1998| pages = 129–131|url=https://books.google.com/books?id=YoZ6CjYNLoQC&pg=PA129| isbn = 978-0-8247-9997-7}}
31. ^{{cite book|author1=Petrov, AA |author2=Balian HV |author3=Troshchenko AT | chapter= Chapter 12. Amino alcohol| title = Organic chemistry| editor= Stadnichuk| edition = 5|location = St. Petersburg.| year = 2002| page = 286| isbn = 5-8194-0067-4}}
32. ^{{cite book|author1=Sheppard, William A. |author2=Sharts, Clay M.| title = Organic Fluorine Chemistry| publisher = W.A. Benjamin| year = 1969| page= 98| isbn = 0-8053-8790-0}}
33. ^{{OrgSynth| author=Kendall, E. C. and McKenzie, B.| year=1923| title=o-Chloromercuriphenol| volume=3| pages=57| collvol=| collvolpages=| prep=cv1p0256}}
34. ^{{OrgSynth| author=Noland, Wayland E.| prep=CV5P0833| title = 2-Nitroethanol| volume=5|pages=833|year=1973}}
35. ^{{cite book| author = Orlova, EY| title = Chemistry and technology of high explosives: Textbook for high schools| edition = 3| publisher = Khimiya| year = 1981| page= 278}}
36. ^{{cite book| author = Vogel, A.I.| title = Vogel's Textbook of practical organic chemistry| edition = 5|location = UK| publisher = Longman Scientific & Technical| year = 1989| page = 1088| isbn = 0-582-46236-3}}
37. ^Watson, James M. and Forward, Cleve (17 April 1984) {{US Patent|4443643}}. "Reaction of benzene with ethylene oxide to produce styrene"
38. ^¹{{cite book| author = Hiraoka M.| title = Crown Compounds. Their Characteristics and Applications| publisher = Kodansha| year = 1982| pages= 33–34| isbn =4-06-139444-4}}
39. ^{{cite journal| author = Roesky H. W.|author2= Schmidt H. G.| title = Reaction of Ethylene Oxide with Sulfur Dioxide in the Presence of Cesium Ions: Synthesis of 1,3,6,9,2 λ ⁴-Tetraoxathia-2-cycloundecanone| journal = Angewandte Chemie International Edition| year = 1985|doi=10.1002/anie.198506951| volume = 24| page = 695| issue = 8}}
40. ^{{cite book|author1=Petrov, AA |author2=Balian HV |author3=Troshchenko AT | chapter= Chapter 4. Ethers| title = Organic chemistry| edition=5| location = St. Petersburg.| year = 2002| pages = 159–160| isbn = 5-8194-0067-4}}
41. ^¹{{cite journal| author = Benson S. W.| title = Pyrolysis of Ethylene Oxide. A Hot Molecule Reaction| doi=10.1063/1.1729851| journal = The Journal of Chemical Physics| year = 1964| volume = 40| page = 105| bibcode = 1964JChPh..40..105B}}
42. ^¹{{cite book| author = Hudlický M.| title = Reductions in Organic Chemistry| location = Chichester| publisher = Ellis Horwood Limited| year = 1984| page = 83| isbn = 0-85312-345-4}}
43. ^{{cite journal| author = Dagaut P.|author2= Voisin D.|author3= Cathonnet M.|author4= Mcguinness M.|author5= Simmie J. M.| title = The oxidation of ethylene oxide in a jet-stirred reactor and its ignition in shock waves| journal = Combustion and Flame| year = 1996| volume = 156| pages = 62–68| doi = 10.1016/0010-2180(95)00229-4}}
44. ^Stapp, Paul R. (21 December 1976) {{US Patent|3998848}} "Cyclodimerization of ethylene oxide"
45. ^¹²{{cite book|author1=Dyment, ON |author2=Kazanskii, KS |author3=Miroshnikov AM | title = Гликоли и другие производные окисей этилена и пропилена|trans-title=Glycols and other derivatives of ethylene oxide and propylene| editor = Dyment, ON| publisher = Khimiya| year = 1976| pages = 214–217}}
46. ^¹{{cite book| title = Polymeric materials encyclopedia| editor= Salamone, Joseph C.| publisher = CRC Press| year = 1996| volume = 8| pages = 6036–6037| isbn = 978-0-8493-2470-3}}
47. ^¹²³{{cite book| chapter= Chapter II. Chemical properties of ethylene oxide| title = Ethylene oxide|editor1=Zimakov, P.V. |editor2=Dyment, O. H. | publisher = Khimiya| year = 1967| pages = 57–85}}
48. ^{{cite journal| author = Neufeld L.M.|author2= Blades A.T.| title = The Kinetics of the Thermal Reactions of Ethylene Oxide| journal = Canadian Journal of Chemistry| year = 1963|doi=10.1139/v63-434| volume = 41| pages = 2956–2961| issue = 12}}
49. ^¹{{cite journal|author = Lifshitz A.|author2= Ben-Hamou H.| title = Thermal reactions of cyclic ethers at high temperatures. 1. Pyrolysis of ethylene oxide behind reflected shocks| journal = The Journal of Physical Chemistry| year = 1983|doi=10.1021/j100233a026| volume = 87| pages = 1782–1787|issue = 10}}
50. ^{{cite book| author = Gilchrist T.| title = Heterocyclic Chemistry| publisher = Pearson Education| year = 1985| pages = 411–412| isbn = 81-317-0793-8}}
51. ^¹{{cite book|author1=Smith, Michael B. |author2=March, Jerry| title = Advanced organic chemistry. Reactions, Mechanisms and Structure| publisher = Wiley-Interscience| year = 2007|url=https://books.google.com/books?id=JDR-nZpojeEC| isbn =0-471-72091-7}}
52. ^{{cite book|author1=Fieser, L. |author2=Fieser, M.| title = Reagents for Organic Synthesis| publisher =Wiley| volume = 7|year=1979| page= 545| isbn =978-0-471-02918-2}}
53. ^{{cite book| author = Sheldon RA| title= Chemicals from synthesis gas: catalytic reactions of CO and, Volume 2| url=https://books.google.com/books?id=s1_rjRUlu1EC&pg=PA193|page=193| publisher = Springer| year = 1983| isbn=90-277-1489-4}}
54. ^¹{{cite book|author1=Fieser, L. |author2=Fieser, M.| title = Reagents for Organic Synthesis| publisher = Wiley| year = 1977|isbn=978-0-471-25873-5| volume = 6| page= 197}}
55. ^Han, Yuan-Zhang and Viswanathan, Krishnan (13 February 2003) {{US Patent|20030032845}} "Hydroformylation of ethylene oxide"
56. ^{{cite book| chapter= Chapter V. Producing ethylene oxide through ethylene| title = Ethylene oxide|editor1=Zimakov, P.V. |editor2=Dyment, O. H. | publisher = Khimiya| year = 1967| pages = 155–182}}
57. ^¹²{{cite book| chapter = Part II. Synthesis of ethylene oxide. Overview of reactions of formation of ethylene oxide and other α-oxides| title = Ethylene oxide|editor1=Zimakov, P.V. |editor2=Dyment, O. H. | publisher = Khimiya| year = 1967| pages = 145–153}}
58. ^{{cite book| author = McMurry J.| title = Organic chemistry| edition = 7| publisher = Thomson| year = 2008| page= 661| isbn = 0-495-11258-5}}
59. ^{{cite journal| author = Norris, J.F.| title = The Manufacture of War Gases in Germany| journal = Journal of Industrial and Engineering Chemistry| year = 1919| volume = 11| pages = 817–829| doi = 10.1021/ie50117a002| issue = 9}}
60. ^¹{{cite book|author1=Weissermel K. |author2=Arpe H-J. | title = Industrial organic chemistry| edition = 4| location = Weinheim| publisher = Wiley-VCH| year = 2003| pages = 145–148| isbn = 978-3-527-30578-0}}
61. ^Market Study: Ethylene. Ceresana.com (December 2010). Retrieved on 2017-05-08.
62. ^{{cite web| date = February 1985| url = http://www.sriconsulting.com/PEP/Public/Reports/Phase_84/RP002D/| title = Process Economics Program Report 2D| work = PEP Report| publisher = SRI Consulting| accessdate = 19 November 2009}}
63. ^¹²³{{cite book| author = Yukelson I.I.| title = The technology of basic organic synthesis| publisher = Khimiya| year = 1968| pages = 554–559}}
64. ^{{cite book| chapter = Catalitic Oxidation of Olefins| title = Advances in catalysis and related subjects|editor1=Eley, D.D. |editor2=Pines, H. |editor3=Weisz, P.B. | location = New York| publisher = Academic Press Inc| year = 1967| volume = 17| pages = 156–157}}
65. ^¹²{{cite book|author1=Bloch H. P. |author2=Godse A. | title = Compressors and modern process applications|publisher = John Wiley and Sons| year = 2006| pages = 295–296| isbn = 978-0-471-72792-7}}
66. ^{{cite web|url=http://www.scidesign.com/Business/EO%20-%20EG%20Process/EO_EG_Process.htm |title=Ethylene Oxide/Ethylene Glycol Process |work=Process Licensing and Engineering |publisher=Scientific Design Company |accessdate=3 October 2009 |deadurl=yes |archiveurl=https://web.archive.org/web/20110716014802/http://www.scidesign.com/Business/EO%20-%20EG%20Process/EO_EG_Process.htm |archivedate=16 July 2011 }}
67. ^{{cite book|author1=Chauvel A. |author2=Lefebvre G. | title = Petrochemical processes 2. Major Oxygenated, Chlorinated and Nitrated Derivatives| edition = 2| location = Paris| publisher = Editions Technip| year = 1989| volume = 2| page= 4| isbn = 2-7108-0563-4}}
68. ^¹{{cite journal| author = Kilty P. A.|author2= Sachtler W. M. H.| title = The mechanism of the selective oxidation of ethylene to ethylene oxide| doi=10.1080/01614947408079624| journal = Catalysis Reviews: Science and Engineering| year = 1974| volume = 10| pages = 1–16}}
69. ^¹{{cite book| author = Lebedev, N.N.| title = Chemistry and technology of basic organic and petrochemical synthesis| edition = 4| publisher = Khimiya| pages = 420–424| isbn = 5-7245-0008-6}}
70. ^{{cite book| author = Gunardson H.| title = Industrial gases in petrochemical processing| location = New York| publisher = Marcel Dekker, Inc.| year = 1998| pages = 131–132| isbn = 0-8247-9908-9}}
71. ^¹{{cite web| date = January 2009| url = http://www.sriconsulting.com/WP/Public/Reports/eo/| title = Ethylene Oxide| work = WP Report| publisher = SRI Consulting| accessdate = 29 September 2009}}
72. ^{{cite web| date = January 2009| url = http://www.sriconsulting.com/WP/Public/Reports/ethylene/| title = Ethylene| work = WP Report| publisher = SRI Consulting| accessdate = 29 September 2009}}
73. ^¹²³{{cite web| author = Devanney M. T.| date = April 2007| url = http://www.sriconsulting.com/PEP/Public/Reports/Phase_2009/RP2I/| title = Ethylene Oxide| work = SEH Peport| publisher = SRI Consulting| accessdate = 19 November 2009}}
74. ^{{cite web| url = http://www.m-kagaku.co.jp/english/corporate/index.html| title = Overview| publisher = Mitsubishi Chemical Corporation| accessdate = 12 October 2009| deadurl = bot: unknown| archiveurl = https://web.archive.org/web/20170225162257/http://www.m-kagaku.co.jp/english/corporate/index.html| archivedate = 25 February 2017| df = dmy-all}}
75. ^{{cite web|url=http://www.shell.com/home/content/chemicals/products_services/our_products/ethylene_oxide_glycols/ethylene_glycols/manufacturing_locations/geismar/ |title=Shell Chemical LP – Geismar, United States of America |work=Manufacturing locations |publisher=Shell Chemicals |accessdate=12 October 2009 |deadurl=yes |archiveurl=https://web.archive.org/web/20101018033052/http://www.shell.com/home/content/chemicals/products_services/our_products/ethylene_oxide_glycols/ethylene_glycols/manufacturing_locations/geismar/ |archivedate=18 October 2010 }}
76. ^{{cite web|url=http://www.shell.com/home/content/chemicals/products_services/our_products/ethylene_oxide_glycols/ethylene_glycols/manufacturing_locations/moerdijk/ |title=Shell Nederland Chemie BV – Moerdijk, Netherlands |work=Manufacturing locations |publisher=Shell Chemicals |accessdate=12 October 2009 |deadurl=yes |archiveurl=https://web.archive.org/web/20101018033102/http://www.shell.com/home/content/chemicals/products_services/our_products/ethylene_oxide_glycols/ethylene_glycols/manufacturing_locations/moerdijk/ |archivedate=18 October 2010 }}
77. ^{{cite web| url = http://www.cnoocshell.com/home/topic.aspx?topic=38| title = Plants/Facilities and Capacity| publisher = CNOOC and Shell Petrochemicals Company Limited| accessdate = 12 October 2009}}{{dead link|date=September 2017 |bot=InternetArchiveBot |fix-attempted=yes }}
78. ^{{cite web| url = http://www.report.basf.com/2008/en/subjects/products/chemicals.html| title = Segment Chemicals – Products| publisher = BASF| accessdate = 12 October 2009}}
79. ^{{cite web|url=http://www.ineosoxide.com/21-Ethylene_Oxide__EO_.htm |title=Ethylene Oxide (EO) |publisher=Ineos Oxide |accessdate=12 October 2009 |deadurl=yes |archiveurl=https://web.archive.org/web/20130608060742/http://www.ineosoxide.com/21-Ethylene_Oxide__EO_.htm |archivedate=8 June 2013 }}
80. ^{{cite web|url=http://www.shell.com/home/content/chemicals/products_services/our_products/ethylene_oxide_glycols/ethylene_glycols/product_overview/ |title=Ethylene oxide product overview |work=Ethylene oxide |publisher=Shell Chemicals |accessdate=8 October 2009 |deadurl=yes |archiveurl=https://archive.is/20121211063906/http://www.shell.com/home/content/chemicals/products_services/our_products/ethylene_oxide_glycols/ethylene_glycols/product_overview/ |archivedate=11 December 2012 }}
81. ^{{cite web |url = http://www.icis.com/v2/chemicals/9075772/ethylene-oxide/uses.html |title = Ethylene Oxide (EO) Uses and Market Data |work = Chemical Intelligence |publisher = Chemical Industry News & Intelligence (ICIS.com) |accessdate = 8 October 2009 |archive-url = https://www.webcitation.org/615sww6sl?url=http://www.icis.com/v2/chemicals/9075772/ethylene-oxide/uses.html |archive-date = 21 August 2011 |dead-url = yes |df = dmy-all}}
82. ^¹{{cite book| chapter= Ethylene| title = Chemical Encyclopedia| editor = Knunyants, I. L.| publisher = "Soviet encyclopedia"| year = 1988| volume = 5| pages = 984–985}}
83. ^{{cite book| title = Handbook of Detergents, Part F: Production|editor1=Zoller, Uri |editor2=Sosis, Paul | publisher = CRC Press| year = 2008| pages = 518–521| isbn = 978-0-8247-0349-3}}
84. ^{{cite web| author = Naqvi, Syed |date = September 2009| url = http://www.sriconsulting.com/PEP/Reports/Phase_2009/RP2I/| title = Process Economics Program Report 2I| work = PEP Peport| publisher = SRI Consulting| accessdate = 20 October 2009}}
85. ^[https://web.archive.org/web/20090514033943/http://www.shell.com/home/content/chemicals/innovation/leading_edge_technology/omega_delivers_ethylene_glycol/omega_delivers_ethylene_glycol.html OMEGA delivers for ethylene glycol makers], Shell (October 2008).
86. ^{{cite book| title = Encyclopedia of chemical processing and design|editor1=McKetta, John J. |editor2=Cunningham, William A. | location = New York| publisher = Marcel Dekker, Inc| year = 1984| volume = 20| pages = 259–260| isbn = 0-8247-2470-4}}
87. ^{{cite web| url = http://www.himtek.ru/cgi-bin/index.cgi?IdS=18&IdP=9&Lang=0| title = Technology of ethanolamine| work = Technology| publisher = Himtek Engineering| accessdate = 22 October 2009|archiveurl = https://web.archive.org/web/20050302144745/http://www.himtek.ru/cgi-bin/index.cgi?IdS=18&IdP=9&Lang=0 |archivedate = 2 March 2005}}
88. ^{{cite book|vauthors=Chekalin MA, Passet BV, Ioffe BA| title = The technology of organic dyes and intermediate products: A manual for technical| edition = 2|publisher = Khimiya| year = 1980| page= 185}}
89. ^[https://www.cdc.gov/niosh/topics/ethyleneoxide/ Ethylene oxide] NIOSH Workplace Safety and Health Topic. Retrieved 15 October 2012.
90. ^¹{{cite book| title = Chemistry and technology of surfactants| editor= Farn, R. J.| publisher = Blackwell Publishing| year = 2006| page = 133| isbn = 1-4051-2696-5}}
91. ^{{cite web|url=http://www.buss-ct.com/e/reaction_technology/alkoxylation.php?navid=36 |title=Alkoxylation |work=BUSS LOOP Reactor |publisher=Buss ChemTech AG |accessdate=21 October 2009 |deadurl=yes |archiveurl=https://web.archive.org/web/20120308161412/http://www.buss-ct.com/e/reaction_technology/alkoxylation.php?navid=36 |archivedate=8 March 2012 }}
92. ^{{cite web|url=http://portal.acs.org/portal/PublicWebSite/education/whatischemistry/landmarks/acrylonitrile/index.htm |archive-url=https://archive.is/20130223214113/http://portal.acs.org/portal/PublicWebSite/education/whatischemistry/landmarks/acrylonitrile/index.htm |dead-url=yes |archive-date=23 February 2013 |title=The Sohio Acrylonitrile Process |work=National Historic Chemical Landmarks |publisher=American Chemical Society |accessdate=25 June 2012 }}
93. ^{{cite web| date = 1 April 2009| url = http://chemanalytica.com/book/novyy_spravochnik_khimika_i_tekhnologa/06_syre_i_produkty_promyshlennosti_organicheskikh_i_neorganicheskikh_veshchestv_chast_II/5015| title = 13.1.3.5. Oxidative ammonolysis of hydrocarbons| publisher = ChemAnalitica.com| accessdate = 22 October 2009}}
94. ^{{cite book| author1 = Andreas, F.| author2 = Grabe, K.| title = Propylenchemie| publisher = Akademie-Verlag| year = 1969| pages = 117–118}}
95. ^¹²³⁴{{cite book |chapter = Vol. 97. 1,3-Butadiene, Ethylene Oxide and Vinyl Halides (Vinyl Fluoride, Vinyl Chloride and Vinyl Bromide) |title = IARC Monographs on the Evaluation of Carcinogenic Risks to Humans |location = Lyon |publisher = International Agency for Research on Cancer |year = 2008 |url = http://monographs.iarc.fr/ENG/Monographs/vol97/ |pages = 185–287 |isbn = 978-92-832-1297-3 |access-date = 11 January 2019 |archive-url = https://web.archive.org/web/20161225052600/http://monographs.iarc.fr/ENG/Monographs/vol97/ |archive-date = 25 December 2016 |dead-url = yes |df = dmy-all}}
96. ^¹{{cite web |url=http://www.environmentwriter.org/resources/backissues/chemicals/ethylene_oxide.htm |archive-url=https://web.archive.org/web/20060828211843/http://www.environmentwriter.org/resources/backissues/chemicals/ethylene_oxide.htm |dead-url=yes |archive-date=28 August 2006 |title=Ethylene oxide |work=Chemical Backgrounders Index |publisher=The Environment Writer |accessdate=29 September 2009 |df=dmy-all }}
97. ^{{cite web| url = http://www.isomedix.com/services/eo-sterilization/| title = Ethylene Oxide Sterilization| publisher = Isometrix| deadurl = bot: unknown| archiveurl = https://web.archive.org/web/20160402020015/http://www.isomedix.com/services/eo-sterilization/| archivedate = 2 April 2016| df = dmy-all}}
98. ^{{cite web| url = http://multimedia.3m.com/mws/mediawebserver?mwsId=SSSSSu7zK1fslxtUO8_x4x_Gev7qe17zHvTSevTSeSSSSSS--| title = 3M on EtO sterilizers and EtO sterilization process.| accessdate = 21 March 2013}}
99. ^{{cite web| url = http://www.isomedix.com/services/eo-sterilization/history-of-ethylene-oxide/| title = History of Ethylene Oxide| publisher = Isometrix| deadurl = bot: unknown| archiveurl = https://web.archive.org/web/20160402022440/http://www.isomedix.com/services/eo-sterilization/history-of-ethylene-oxide/| archivedate = 2 April 2016| df = dmy-all}}
100. ^{{cite web |url = http://www.ovguide.com/harold-willids-andersen-9202a8c04000641f800000000f160f69# |title = Dr. H.W. Andersen's patent of Ethylene Oxide flexible chamber system. |accessdate = 21 March 2013 |archive-url = https://web.archive.org/web/20160306193908/http://www.ovguide.com/harold-willids-andersen-9202a8c04000641f800000000f160f69 |archive-date = 6 March 2016 |dead-url = yes |df = dmy-all}}
101. ^{{cite web| url = http://anpro.com/index.htm| title = Andersen Products| accessdate = 21 March 2013}}
102. ^{{cite web|url=http://cal.vet.upenn.edu/projects/surgery/2220.htm |title=University of Pennsylvania, EtO uses in veterinarian practices. |accessdate=21 March 2013 |deadurl=yes |archiveurl=https://web.archive.org/web/20131109225657/http://cal.vet.upenn.edu/projects/surgery/2220.htm |archivedate=9 November 2013 }}
103. ^{{cite web| url = http://www.epa.gov/ttn/atw/area/sterilizers_3_7_08.pdf| title = EPA on EtO regulation| accessdate = 21 March 2013}}
104. ^¹{{cite book|url=https://books.google.com/books?id=ZzlNgS70OHAC&pg=PA136|page=136|title=Weapons of mass destruction: an encyclopedia of worldwide policy, technology, and history, Volume 2|author1=Croddy, Eric |author2=Wirtz, James J. |isbn=1-85109-490-3|publisher=ABC-CLIO|year=2005}}
105. ^¹{{cite book|url=https://books.google.com/books?id=ATiYCfo1VcEC&pg=PA142|page=142|title=Explosives|author1=Meyer, Rudolf |author2=Köhler, Josef |author3=Homburg, Axel |publisher=Wiley-VCH|year=2007|isbn=3-527-31656-6}}
106. ^Hardy, Periam B.; Gay, Lewis L. and Husler, Edward L. (2 January 1979) {{US Patent|4132170}} "Fuel-air type bomb"
107. ^{{cite book|title=Toxicological Profile for 2-Butoxyethanol and 2-butoxyethanol acetate|date=August 1998|publisher=US Dept of Health and Human Services|author=Harris O.|displayauthors=etal }}
108. ^¹{{cite book| chapter = Chapter IV Methods of analysis of ethylene oxide| title = Ethylene oxide| editor1=Zimakov, P.V.| editor2=Dyment, O. H.| publisher = Khimiya| year = 1967| pages = 128–140}}
109. ^{{cite web|url=http://www.safework.ru/ilo/ICSC/cards/view/?0155 |title=Ethylene oxide |work=ICSC/International Chemical Safety Cards |publisher=Institute of Industrial Safety, Labour Protection and Social Partnership |accessdate=21 September 2009 |deadurl=yes |archiveurl=https://web.archive.org/web/20051228201427/http://www.safework.ru/ilo/ICSC/cards/view/?0155 |archivedate=28 December 2005 }}
110. ^{{cite web|url=http://www.csb.gov/csb-issues-final-report-in-2004-explosion-at-sterigenics-international-facility-in-ontario-california-notes-lack-of-engineering-controls-understanding-of-process-hazards/|title=CSB Issues Final Report in 2004 Explosion at Sterigenics International Facility in Ontario, California: Notes Lack of Engineering Controls, Understanding of Process Hazards - Investigations - News - CSB |author= |date= |website=www.csb.gov |accessdate=29 March 2018}}
111. ^{{cite web|url=http://www.csb.gov/videos/ethylene-oxide-explosion-at-sterigenics/|title=Ethylene Oxide Explosion at Sterigenics - Safety Videos - Multimedia - CSB |author=|date= |website=www.csb.gov |accessdate=29 March 2018}}
112. ^{{cite web|url=https://www.osha.gov/pls/imis/establishment.inspection_detail?id=105522072|title=OSHA Inspection Detail |author= |date= |website=www.osha.gov |accessdate=24 May 2018}}
113. ^{{cite web| year = 1988| url = http://www.inchem.org/documents/hsg/hsg/hsg016.htm| title = Ethylene Oxide| work = Health and Safety Guide| publisher = International Programme on Chemical Safety (IPCS) INCHEM| accessdate = 23 September 2009}}
114. ^{{cite web|date=10 January 2009 |url=http://www.sonoma-county.org/des/pdf/fire/bulletins/info_bulletin_nfpa_marking2009_04n.pdf |title=Informational Bulletin NFPA-04N 2009 |publisher=Department of Emergency Services, County of Sonoma |accessdate=23 October 2009 |deadurl=yes |archiveurl=https://web.archive.org/web/20090804080033/http://www.sonoma-county.org/des/pdf/fire/bulletins/info_bulletin_nfpa_marking2009_04n.pdf |archivedate=4 August 2009 }}
115. ^{{cite web |url = http://s01.static-shell.com/content/dam/shell/static/chemicals/downloads/products-services/ethylene-oxide-safetyliteraturevi.pdf |archive-url = https://web.archive.org/web/20160303235017/http://s01.static-shell.com/content/dam/shell/static/chemicals/downloads/products-services/ethylene-oxide-safetyliteraturevi.pdf |dead-url = yes |archive-date = 3 March 2016 |title = Ethylene Oxide Safety Literature |publisher = Shell Chemicals |accessdate = 23 October 2009}}
116. ^{{cite web|url=http://naspco.com/sterilization/|title=Ethylene Oxide Sterilization|last=|first=|date=|website=NASPCO|access-date=2017-02-10|archive-url=https://web.archive.org/web/20180708031254/http://naspco.com/sterilization/|archive-date=8 July 2018|dead-url=yes|df=dmy-all}}
117. ^{{cite web|url=https://microbeonline.com/ethylene-oxide-eto-properties-mode-action-uses/|title=Ethylene Oxide (ETO): Properties, Mode of Action and Uses|last=|first=|date=|website=Microbe Online|access-date=2017-02-10}}
118. ^¹²{{cite web| date = 1 April 2009| url = http://chemanalytica.com/book/novyy_spravochnik_khimika_i_tekhnologa/11_radioaktivnye_veshchestva_vrednye_veshchestva_gigienicheskie_normativy/5177| title = Harmful substances. Section 4. Heterocyclic compounds. Triplex heterocyclic compounds| publisher = ChemAnalitica.com| accessdate = 21 September 2009}}
119. ^{{cite web| author = Collins J. L.| url = http://base.safework.ru/iloenc?hdoc&nd=857300040&nh=0| title = Epoxy compounds| work = Encyclopedia of the ILO| publisher = Institute of Industrial Safety, Labour Protection and Social Partnership| accessdate = 25 September 2009}}
120. ^{{cite book |chapter = Vol. 60. Some Industrial Chemicals |title = IARC Monographs on the Evaluation of Carcinogenic Risks to Humans |location = Lyon |publisher = International Agency for Research on Cancer |year = 1999 |url = http://monographs.iarc.fr/ENG/Monographs/vol60/ |isbn = 978-92-832-1297-3 |access-date = 28 June 2007 |archive-url = https://web.archive.org/web/20160303232338/http://monographs.iarc.fr/ENG/Monographs/vol60/ |archive-date = 3 March 2016 |dead-url = yes |df = dmy-all}}
121. ^{{Cite journal | doi = 10.1023/A:1024891529592|pmid=12948284| title=Ethylene oxide and breast cancer incidence in a cohort study of 7576 women (United States)| year = 2003| last1 = Steenland | first1 = K. | journal = Cancer Causes and Control| volume = 14| issue = 6| pages = 531–9| last2 = Whelan | first2 = E. | last3 = Deddens | first3 = J. | last4 = Stayner | first4 = L. | last5 = Ward | first5 = E. }}
122. ^{{Cite journal| pmid = 14691266| pmc = 1757803| year = 2004| author1 = Steenland| first1 = K| title = Mortality analyses in a cohort of 18 235 ethylene oxide exposed workers: Follow up extended from 1987 to 1998| journal = Occupational and Environmental Medicine| volume = 61| issue = 1| pages = 2–7| last2 = Stayner| first2 = L| last3 = Deddens| first3 = J}}
123. ^¹[https://web.archive.org/web/20120313031850/http://www.atsdr.cdc.gov/toxprofiles/tp137.pdf Toxicological Profile For Ethylene Oxide]. Agency for Toxic Substances and Disease Registry, US Public Health Services
124. ^{{cite book|author1=Carson P.A. |author2=Mumford C.J. | title = Hazardous Chemicals Handbooks| location = Oxford| publisher = Butterworth-Heinemann Ltd| year = 1994| page = 85| isbn = 0-7506-0278-3}}
125. ^[https://www.cdc.gov/niosh/idlh/intridl4.html Immediately Dangerous To Life or Health (IDLH) Values]. Cdc.gov. Retrieved on 2017-05-08.
126. ^{{cite web| last = Chemicals Regulation Directorate| title = Banned and Non-Authorised Pesticides in the United Kingdom| url = http://www.pesticides.gov.uk/guidance/industries/pesticides/topics/pesticide-approvals/pesticides-registration/Withdrawal-and-Restrictions/banned-and-non-authorised-pesticides| accessdate = 1 December 2009}}
127. ^¹{{cite book|author=Simmons, H. Leslie|title=Building Materials: Dangerous Properties of Products in MasterFormat Divisions 7 and 9|url=https://books.google.com/books?id=MH9DrW0UGvwC&pg=PA146|year=1997|publisher=John Wiley & Sons|isbn=978-0-442-02289-1|page=146}} Codes {{Webarchive|url=https://web.archive.org/web/20150402124719/http://chemistry.umeche.maine.edu/Safety/ReadMSDS.html |date=2 April 2015 }}.
128. ^{{Cite book|title=Evaluation of the Inhalation Carcinogenicity of Ethylene Oxide|last=|first=|publisher=US Environmental Protection Agency|year=2016|isbn=|location=|pages=|url=https://cfpub.epa.gov/ncea/iris/iris_documents/documents/toxreviews/1025tr.pdf}}
129. ^¹{{cite journal |last=Dutia |first=Pankaj |title=Ethylene Oxide: A Techno-Commercial Profile |url=http://www.chemicalweekly.com/Profiles/Ethylene_Oxide.pdf |journal=Chemical Weekly |date=26 January 2010|deadurl = yes|archiveurl = https://web.archive.org/web/20150402145434/http://www.chemicalweekly.com/Profiles/Ethylene_Oxide.pdf|archivedate = 2 April 2015}}

History

Molecular structure and properties

Physical properties

Chemical properties

Addition of water and alcohols

Addition of carboxylic acids and their derivatives

Adding ammonia and amines

Halide addition

Metalorganic addition

Other addition reactions

Addition of hydrogen cyanide

Addition of hydrogen sulfide and mercaptans

Addition of nitrous and nitric acids

Reaction with compounds containing active methylene groups

Alkylation of aromatic compounds

Synthesis of crown ethers

Isomerization

Reduction reaction

Oxidation

Dimerization

Polymerization

Thermal decomposition

Other reactions

Laboratory synthesis

Dehydrochlorination of ethylene and its derivatives

Direct oxidation of ethylene by peroxy acids

Other preparative methods

Industrial synthesis

History

Chlorohydrin process of production of ethylene oxide

Direct oxidation of ethylene

Usage in global industry

Chemistry and kinetics of the direct oxidation process

Process overview

World production of ethylene oxide

Applications

Production of ethylene glycol

Production of glycol ethers

Production of ethanolamines

Production of ethoxylates

Production of acrylonitrile

Non-industrial uses

Healthcare sterilant

Niche uses

Identification of ethylene oxide

Fire and explosion hazards

Physiological effects

Effect on microorganisms

Effects on humans and animals

Global demand

References

Cited sources

External links