1. {{anchor|Coherent SI units}} Units and prefixes
    Base units  Derived units  Prefixes  Non-SI units accepted for use with SI  Common notions of the metric units 

2. Lexicographic conventions
    Unit names  Unit symbols and the values of quantities {{anchor|SI_writing_style}}  General rules  Printing SI symbols  Examples of the variety of symbols in use around the world for kilometres per hour 

3. International System of Quantities

4. Realisation of units

5. Evolution of the SI
    Changes to the SI  2019 redefinitions 

6. History
    The improvisation of units  Metre Convention  The cgs and MKS systems  The Practical system of units  Birth of the SI 

7. See also

8. Notes

9. References

10. Further reading

11. External links

The International System of Units (SI, abbreviated from the French {{lang|fr|Système international (d'unités)}}) is the modern form of the metric system, and is the most widely used system of measurement. It comprises a coherent system of units of measurement built on seven base units, which are the ampere, kelvin, second, metre, kilogram, candela, mole, and a set of twenty prefixes to the unit names and unit symbols that may be used when specifying multiples and fractions of the units. The system also specifies names for 22 derived units, such as lumen and watt, for other common physical quantities.

The base units are derived from invariant constants of nature, such as the speed of light in vacuum and the triple point of water, which can be observed and measured with great accuracy, and one physical artefact. The artefact is the international prototype kilogram, certified in 1889, and consisting of a cylinder of platinum-iridium, which nominally has the same mass as one litre of water at the freezing point. Its stability has been a matter of significant concern, culminating in a revision of the definition of the base units entirely in terms of constants of nature, scheduled to be put into effect on 20 May 2019.^[1]

Derived units may be defined in terms of base units or other derived units. They are adopted to facilitate measurement of diverse quantities. The SI is intended to be an evolving system; units and prefixes are created and unit definitions are modified through international agreement as the technology of measurement progresses and the precision of measurements improves. The most recent derived unit, the katal, was defined in 1999.

The reliability of the SI depends not only on the precise measurement of standards for the base units in terms of various physical constants of nature, but also on precise definition of those constants. The set of underlying constants is modified as more stable constants are found, or may be more precisely measured. For example, in 1983 the metre was redefined as the distance that light propagates in vacuum in a given fraction of a second, thus making the value of the speed of light in terms of the defined units exact.

The motivation for the development of the SI was the diversity of units that had sprung up within the centimetre–gram–second (CGS) systems (specifically the inconsistency between the systems of electrostatic units and electromagnetic units) and the lack of coordination between the various disciplines that used them. The General Conference on Weights and Measures (French: {{lang|fr|Conférence générale des poids et mesures}} – CGPM), which was established by the Metre Convention of 1875, brought together many international organisations to establish the definitions and standards of a new system and standardise the rules for writing and presenting measurements. The system was published in 1960 as a result of an initiative that began in 1948. It is based on the metre–kilogram–second system of units (MKS) rather than any variant of the CGS. Since then, the SI has been adopted by all countries except the United States, Liberia and Myanmar.^[2]

{{anchor|Coherent SI units}} Units and prefixes

The International System of Units consists of a set of base units, derived units, and a set of decimal-based multipliers that are used as prefixes.^[3]{{rp|103–106}} The units, excluding prefixed units,^[3] form a coherent system of units, which is based on a system of quantities in such a way that the equations between the numerical values expressed in coherent units have exactly the same form, including numerical factors, as the corresponding equations between the quantities. For example, 1 N = 1 kg × 1 m/s² says that one newton is the force required to accelerate a mass of one kilogram at one metre per second squared, as related through the principle of coherence to the equation relating the corresponding quantities: {{math|1=F = m × a}}.

Derived units apply to derived quantities, which may by definition be expressed in terms of base quantities, and thus are not independent; for example, electrical conductance is the inverse of electrical resistance, with the consequence that the siemens is the inverse of the ohm, and similarly, the ohm and siemens can be replaced with a ratio of an ampere and a volt, because those quantities bear a defined relationship to each other.^[4] Other useful derived quantities can be specified in terms of the SI base and derived units that have no named units in the SI system, such as acceleration, which is defined in SI units as m/s².

Base units

The SI base units are the building blocks of the system and all the other units are derived from them. When Maxwell first introduced the concept of a coherent system, he identified three quantities that could be used as base units: mass, length and time. Giorgi later identified the need for an electrical base unit, for which the unit of electric current was chosen for SI. Another three base units (for temperature, amount of substance and luminous intensity) were added later.

The early metric systems defined a unit of weight as a base unit, while the SI defines an analogous unit of mass. In everyday use, these are mostly interchangeable, but in scientific contexts the difference matters. Mass, strictly the inertial mass, represents a quantity of matter. It relates the acceleration of a body to the applied force via Newton's law, {{nowrap|1=F = m × a}}: force equals mass times acceleration. A force of 1 N (newton) applied to a mass of 1 kg will accelerate it at 1 m/s². This is true whether the object is floating in space or in a gravity field e.g. at the Earth's surface. Weight is the force exerted on a body by a gravitational field, and hence its weight depends on the strength of the gravitational field. Weight of a 1 kg mass at the Earth's surface is {{nowrap|m × g}}; mass times the acceleration due to gravity, which is 9.81 newtons at the Earth's surface and is about 3.5 newtons at the surface of Mars. Since the acceleration due to gravity is local and varies by location and altitude on the Earth, weight is unsuitable for precision measurements of a property of a body, and this makes a unit of weight unsuitable as a base unit.

Derived units

The derived units in the SI are formed by powers, products or quotients of the base units and are unlimited in number.^[3]{{rp|103}}^[6]{{rp|3}} Derived units are associated with derived quantities; for example, velocity is a quantity that is derived from the base quantities of time and length, and thus the SI derived unit is metre per second (symbol m/s). The dimensions of derived units can be expressed in terms of the dimensions of the base units.

Combinations of base and derived units may be used to express other derived units. For example, the SI unit of force is the newton (N), the SI unit of pressure is the pascal (Pa)—and the pascal can be defined as one newton per square metre (N/m²).^[14]

Prefixes

Prefixes are added to unit names to produce multiples and sub-multiples of the original unit. All of these are integer powers of ten, and above a hundred or below a hundredth all are integer powers of a thousand. For example, kilo- denotes a multiple of a thousand and milli- denotes a multiple of a thousandth, so there are one thousand millimetres to the metre and one thousand metres to the kilometre. The prefixes are never combined, so for example a millionth of a metre is a micrometre, not a millimillimetre. Multiples of the kilogram are named as if the gram were the base unit, so a millionth of a kilogram is a milligram, not a microkilogram.^[3]{{rp|122}}^[15]{{rp|14}} When prefixes are used to form multiples and submultiples of SI base and derived units, the resulting units are no longer coherent.^[3]{{rp|7}}

The BIPM specifies twenty prefixes for the International System of Units (SI):

Non-SI units accepted for use with SI

Many non-SI units continue to be used in the scientific, technical, and commercial literature. Some units are deeply embedded in history and culture, and their use has not been entirely replaced by their SI alternatives. The CIPM recognised and acknowledged such traditions by compiling a list of non-SI units accepted for use with SI:^[3]

Certain units of time, angle, and legacy non-SI units have a long history of consistent use. Most societies have used the solar day and its non-decimal subdivisions as a basis of time and, unlike the foot or the pound, these were the same regardless of where they were being measured. The radian, being {{sfrac|2π}} of a revolution, has mathematical advantages but it is cumbersome for navigation{{fact|date=June 2018}}, and, as with time, the units used in navigation are largely consistent around the world. The tonne, litre, and hectare were adopted by the CGPM in 1879 and have been retained as units that may be used alongside SI units, having been given unique symbols. The catalogued units are given below:

Common notions of the metric units

The basic units of the metric system, as originally defined, represented common quantities or relationships in nature. They still do – the modern precisely defined quantities are refinements of definition and methodology, but still with the same magnitudes. In cases where laboratory precision may not be required or available, or where approximations are good enough, the original definitions may suffice.^[16]

• A second is 1/60 of a minute, which is 1/60 of an hour, which is 1/24 of a day, so a second is 1/86400 of a day; a second is the time it takes a dense object to freely fall 4.9 metres from rest.
• The metre is close to the length of a pendulum that has a period of 2 seconds; most dining tabletops are about 0.75 metre high; a very tall human (basketball forward) is about 2 metres tall.
• The kilogram is the mass of a litre of cold water; a cubic centimetre or millilitre of water has a mass of one gram; a 1-euro coin, 7.5 g; a Sacagawea US 1-dollar coin, 8.1 g; a UK 50-pence coin, 8.0 g.
• A candela is about the luminous intensity of a moderately bright candle, or 1 candle power; a 60 W tungsten-filament incandescent light bulb has a luminous intensity of about 64 candela.
• A mole of a substance has a mass that is its molecular mass expressed in units of grams; the mass of a mole of table salt is 58.4 g.
• A temperature difference of one kelvin is the same as one degree Celsius: 1/100 of the temperature differential between the freezing and boiling points of water at sea level; the absolute temperature in kelvins is the temperature in degrees Celsius plus about 273; human body temperature is about 37 °C or 310 K.
• A 60 W incandescent light bulb consumes 0.5 amperes at 120 V (US mains voltage) and about 0.26 amperes at 230 V (European mains voltage).

Lexicographic conventions

Unit names

The symbols for the SI units are intended to be identical, regardless of the language used,^[3]{{rp|130–135}} but unit names are ordinary nouns and use the character set and follow the grammatical rules of the language concerned. Names of units follow the grammatical rules associated with common nouns: in English and in French they start with a lowercase letter (e.g., newton, hertz, pascal), even when the symbol for the unit begins with a capital letter. This also applies to "degrees Celsius", since "degree" is the unit.^[17][18] The official British and American spellings for certain SI units differ – British English, as well as Australian, Canadian and New Zealand English, uses the spelling deca-, metre, and litre whereas American English uses the spelling deka-, meter, and liter, respectively.^[6]{{rp|3}}

Unit symbols and the values of quantities {{anchor|SI_writing_style}}

Although the writing of unit names is language-specific, the writing of unit symbols and the values of quantities is consistent across all languages and therefore the SI Brochure has specific rules in respect of writing them.^[3]{{rp|130–135}} The guideline produced by the National Institute of Standards and Technology (NIST)^[19] clarifies language-specific areas in respect of American English that were left open by the SI Brochure, but is otherwise identical to the SI Brochure.^[20]

General rules

General rules^[21] for writing SI units and quantities apply to text that is either handwritten or produced using an automated process:

• The value of a quantity is written as a number followed by a space (representing a multiplication sign) and a unit symbol; e.g., 2.21 kg, {{val|7.3|e=2|u=m²}}, 22 K. This rule explicitly includes the percent sign (%)^[3]{{rp |134}} and the symbol for degrees of temperature (°C).^[3]{{rp|133}} Exceptions are the symbols for plane angular degrees, minutes, and seconds (°, ′, and ″), which are placed immediately after the number with no intervening space.
• Symbols are mathematical entities, not abbreviations, and as such do not have an appended period/full stop (.), unless the rules of grammar demand one for another reason, such as denoting the end of a sentence.
• A prefix is part of the unit, and its symbol is prepended to a unit symbol without a separator (e.g., k in km, M in MPa, G in GHz, μ in μg). Compound prefixes are not allowed. A prefixed unit is atomic in expressions (e.g., km² is equivalent to (km)²).
• Symbols for derived units formed by multiplication are joined with a centre dot (⋅) or a non-breaking space; e.g., N⋅m or N m.
• Symbols for derived units formed by division are joined with a solidus (/), or given as a negative exponent. E.g., the "metre per second" can be written m/s, m s⁻¹, m⋅s⁻¹, or {{sfrac|m|s}}. A solidus must not be used more than once in a given expression without parentheses to remove ambiguities; e.g., kg/(m⋅s²) and kg⋅m⁻¹⋅s⁻² are acceptable, but kg/m/s² is ambiguous and unacceptable.

• The first letter of symbols for units derived from the name of a person is written in upper case; otherwise, they are written in lower case. E.g., the unit of pressure is named after Blaise Pascal, so its symbol is written "Pa", but the symbol for mole is written "mol". Thus, "T" is the symbol for tesla, a measure of magnetic field strength, and "t" the symbol for tonne, a measure of mass. Since 1979, the litre may exceptionally be written using either an uppercase "L" or a lowercase "l", a decision prompted by the similarity of the lowercase letter "l" to the numeral "1", especially with certain typefaces or English-style handwriting. The American NIST recommends that within the United States "L" be used rather than "l".
• Symbols do not have a plural form, e.g., 25 kg, but not 25 {{Not a typo|kgs}}.
• Uppercase and lowercase prefixes are not interchangeable. E.g., the quantities 1 mW and 1 MW represent two different quantities (milliwatt and megawatt).
• The symbol for the decimal marker is either a point or comma on the line. In practice, the decimal point is used in most English-speaking countries and most of Asia, and the comma in most of Latin America and in continental European countries.^[22]
• Spaces should be used as a thousands separator ({{val|1000000}}) in contrast to commas or periods (1,000,000 or 1.000.000) to reduce confusion resulting from the variation between these forms in different countries.
• Any line-break inside a number, inside a compound unit, or between number and unit should be avoided. Where this is not possible, line breaks should coincide with thousands separators.
• Because the value of "billion" and "trillion" varies between languages, the dimensionless terms "ppb" (parts per billion) and "ppt" (parts per trillion) should be avoided. The SI Brochure does not suggest alternatives.

Printing SI symbols

The rules covering printing of quantities and units are part of ISO 80000-1:2009.^[23]

Further rules^[21] are specified in respect of production of text using printing presses, word processors, typewriters and the like.

Examples of the variety of symbols in use around the world for kilometres per hour

The denominator "hour" (h) is often translated to the country language:

Countries with historical ties to the United States often mix up the international "km/h" with the American "MPH":

International System of Quantities

The quantities and equations that provide the context in which the SI units are defined are now referred to as the International System of Quantities (ISQ).

The system is based on the quantities underlying each of the seven base units of the SI. Other quantities, such as area, pressure, and electrical resistance, are derived from these base quantities by clear non-contradictory equations. The ISQ defines the quantities that are measured with the SI units.^[28] The ISQ is defined in the international standard ISO/IEC 80000, and was finalised in 2009 with the publication of ISO 80000-1.^[29]

Realisation of units

Metrologists carefully distinguish between the definition of a unit and its realisation. The definition of each base unit of the SI is drawn up so that it is unique and provides a sound theoretical basis on which the most accurate and reproducible measurements can be made. The realisation of the definition of a unit is the procedure by which the definition may be used to establish the value and associated uncertainty of a quantity of the same kind as the unit. A description of the mise en pratique^[31] of the base units is given in an electronic appendix to the SI Brochure.^[32][24]{{rp|168–169}}

The published mise en pratique is not the only way in which a base unit can be determined: the SI Brochure states that "any method consistent with the laws of physics could be used to realise any SI unit."^[24]{{rp|111}} In the current (2016) exercise to overhaul the definitions of the base units, various consultative committees of the CIPM have required that more than one mise en pratique shall be developed for determining the value of each unit.{{citation needed|date=November 2012}} In particular:

• At least three separate experiments be carried out yielding values having a relative standard uncertainty in the determination of the kilogram of no more than {{val|5|e=-8}} and at least one of these values should be better than {{val|2|e=-8}}. Both the Kibble balance and the Avogadro project should be included in the experiments and any differences between these be reconciled.^[33][34]
• When the kelvin is being determined, the relative uncertainty of the Boltzmann constant derived from two fundamentally different methods such as acoustic gas thermometry and dielectric constant gas thermometry be better than one part in {{val|e=-6}} and that these values be corroborated by other measurements.^[35]

Evolution of the SI

Changes to the SI

The International Bureau of Weights and Measures (BIPM) has described SI as "the modern metric system".^[24]{{rp|95}} Changing technology has led to an evolution of the definitions and standards that has followed two principal strands – changes to SI itself, and clarification of how to use units of measure that are not part of SI but are still nevertheless used on a worldwide basis.

Since 1960 the CGPM has made a number of changes to the SI to meet the needs of specific fields, notably chemistry and radiometry. These are mostly additions to the list of named derived units, and include the mole (symbol mol) for an amount of substance, the pascal (symbol Pa) for pressure, the siemens (symbol S) for electrical conductance, the becquerel (symbol Bq) for "activity referred to a radionuclide", the gray (symbol Gy) for ionising radiation, the sievert (symbol Sv) as the unit of dose equivalent radiation, and the katal (symbol kat) for catalytic activity.^[24]{{rp|156}}^[36][24]{{rp|156}}^[24]{{rp|158}}^[24]{{rp|159}}^[24]{{rp|165}}

Acknowledging the advancement of precision science at both large and small scales, the range of defined prefixes pico- (10⁻¹²) to tera- (10¹²) was extended to 10⁻²⁴ to 10²⁴.^[24]{{rp|152}}^[24]{{rp|158}}^[24]{{rp|164}}

The 1960 definition of the standard metre in terms of wavelengths of a specific emission of the krypton 86 atom was replaced with the distance that light travels in a vacuum in exactly {{sfrac|{{val|299792458}}}} second, so that the speed of light is now an exactly specified constant of nature.

A few changes to notation conventions have also been made to alleviate lexicographic ambiguities. An analysis under the aegis of CSIRO, published in 2009 by the Royal Society, has pointed out the opportunities to finish the realisation of that goal, to the point of universal zero-ambiguity machine readability.^[37]

2019 redefinitions

After the metre was redefined in 1960, the kilogram remained the only SI base unit directly based on a specific physical artefact, the international prototype of the kilogram (IPK), for its definition and thus the only unit that was still subject to periodic comparisons of national standard kilograms with the IPK.^[38] During the 2nd and 3rd Periodic Verification of National Prototypes of the Kilogram, a significant divergence had occurred between the mass of the IPK and all of its official copies stored around the world: the copies had all noticeably increased in mass with respect to the IPK. During extraordinary verifications carried out in 2014 preparatory to redefinition of metric standards, continuing divergence was not confirmed. Nonetheless, the residual and irreducible instability of a physical IPK undermined the reliability of the entire metric system to precision measurement from small (atomic) to large (astrophysical) scales.

A proposal was made that:

• In addition to the speed of light, four constants of nature – the Planck constant, an elementary charge, the Boltzmann constant and the Avogadro number – be defined to have exact values
• The International Prototype Kilogram be retired
• The current definitions of the kilogram, ampere, kelvin and mole be revised
• The wording of base unit definitions should change emphasis from explicit unit to explicit constant definitions.

In 2015, the CODATA task group on fundamental constants announced special submission deadlines for data to compute the final values for the new definitions.^[39]

The new definitions were adopted at the 26th CGPM in November 2018, and will come into effect in May 2019.^[40]

History

The improvisation of units

The units and unit magnitudes of the metric system which became the SI were improvised piecemeal from everyday physical quantities starting in the mid-18th century. Only later were they moulded into an orthogonal coherent decimal system of measurement.

The degree centigrade as a unit of temperature resulted from the scale devised by Swedish astronomer Anders Celsius in 1742. His scale counter-intuitively designated 100 as the freezing point of water and 0 as the boiling point. Independently, in 1743, the French physicist Jean-Pierre Christin described a scale with 0 as the freezing point of water and 100 the boiling point. The scale became known as the centi-grade, or 100 gradations of temperature, scale.

The metric system was developed from 1791 onwards by a committee of the French Academy of Sciences, commissioned to create a unified and rational system of measures.^[42] The group, which included preeminent French men of science,^[43]{{rp|89}} used the same principles for relating length, volume, and mass that had been proposed by the English clergyman John Wilkins in 1668^[44][45] and the concept of using the Earth's meridian as the basis of the definition of length, originally proposed in 1670 by the French abbot Mouton.^[46][47]

In March 1791, the Assembly adopted the committee's proposed principles for the new decimal system of measure including the metre defined to be 1/10,000,000th of the length of the quadrant of earth's meridian passing through Paris, and authorised a survey to precisely establish the length of the meridian. In July 1792, the committee proposed the names metre, are, litre and grave for the units of length, area, capacity, and mass, respectively. The committee also proposed that multiples and submultiples of these units were to be denoted by decimal-based prefixes such as centi for a hundredth and kilo for a thousand.^[48]{{rp|82}}

Later, during the process of adoption of the metric system, the Latin gramme and kilogramme, replaced the former provincial terms gravet (1/1000 grave) and grave. In June 1799, based on the results of the meridian survey, the standard mètre des Archives and kilogramme des Archives were deposited in the French National Archives. Subsequently, that year, the metric system was adopted by law in France.^[50]

^[51] The French system was short-lived due to its unpopularity. Napoleon ridiculed it, and in 1812, introduced a replacement system, the mesures usuelles or "customary measures" which restored many of the old units, but redefined in terms of the metric system.

During the first half of the 19th century there was little consistency in the choice of preferred multiples of the base units: typically the myriametre ({{val|10000}} metres) was in widespread use in both France and parts of Germany, while the kilogram ({{val|1000}} grams) rather than the myriagram was used for mass.^[41]

In 1832, the German mathematician Carl Friedrich Gauss, assisted by Wilhelm Weber, implicitly defined the second as a base unit when he quoted the Earth's magnetic field in terms of millimetres, grams, and seconds.^[52] Prior to this, the strength of the Earth's magnetic field had only been described in relative terms. The technique used by Gauss was to equate the torque induced on a suspended magnet of known mass by the Earth's magnetic field with the torque induced on an equivalent system under gravity. The resultant calculations enabled him to assign dimensions based on mass, length and time to the magnetic field.^[53][54]

A candlepower as a unit of illuminance was originally defined by an 1860 English law as the light produced by a pure spermaceti candle weighing {{frac|1|6}} pound (76 grams) and burning at a specified rate. Spermaceti, a waxy substance found in the heads of sperm whales, was once used to make high-quality candles. At this time the French standard of light was based upon the illumination from a Carcel oil lamp. The unit was defined as that illumination emanating from a lamp burning pure rapeseed oil at a defined rate. It was accepted that ten standard candles were about equal to one Carcel lamp.

Metre Convention

A French-inspired initiative for international cooperation in metrology led to the signing in 1875 of the Metre Convention, also called Treaty of the Metre, by 17 nations.^[56][43]{{rp|353–354}} Initially the convention only covered standards for the metre and the kilogram. In 1921, the Metre Convention was extended to include all physical units, including the ampere and others thereby enabling the CGPM to address inconsistencies in the way that the metric system had been used.^[57][24]{{rp|96}}

A set of 30 prototypes of the metre and 40 prototypes of the kilogram,^[58] in each case made of a 90% platinum-10% iridium alloy, were manufactured by British metallurgy specialty firm and accepted by the CGPM in 1889. One of each was selected at random to become the International prototype metre and International prototype kilogram that replaced the mètre des Archives and kilogramme des Archives respectively. Each member state was entitled to one of each of the remaining prototypes to serve as the national prototype for that country.^[59]

The treaty also established a number of international organisations to oversee the keeping of international standards of measurement:^[60]

The cgs and MKS systems

In the 1860s, James Clerk Maxwell, William Thomson (later Lord Kelvin) and others working under the auspices of the British Association for the Advancement of Science, built on Gauss' work and formalised the concept of a coherent system of units with base units and derived units christened the centimetre–gram–second system of units in 1874. The principle of coherence was successfully used to define a number of units of measure based on the CGS, including the erg for energy, the dyne for force, the barye for pressure, the poise for dynamic viscosity and the stokes for kinematic viscosity.^[62]

In 1879, the CIPM published recommendations for writing the symbols for length, area, volume and mass, but it was outside its domain to publish recommendations for other quantities. Beginning in about 1900, physicists who had been using the symbol "μ" (mu) for "micrometre" or "micron", "λ" (lambda) for "microlitre", and "γ" (gamma) for "microgram" started to use the symbols "μm", "μL" and "μg".^[63]

At the close of the 19th century three different systems of units of measure existed for electrical measurements: a CGS-based system for electrostatic units, also known as the Gaussian or ESU system, a CGS-based system for electromechanical units (EMU) and an International system based on units defined by the Metre Convention.^[64] for electrical distribution systems.

Attempts to resolve the electrical units in terms of length, mass, and time using dimensional analysis was beset with difficulties—the dimensions depended on whether one used the ESU or EMU systems.^[65] This anomaly was resolved in 1901 when Giovanni Giorgi published a paper in which he advocated using a fourth base unit alongside the existing three base units. The fourth unit could be chosen to be electric current, voltage, or electrical resistance.^[66] Electric current with named unit 'ampere' was chosen as the base unit, and the other electrical quantities derived from it according to the laws of physics. This became the foundation of the MKS system of units.

In the late 19th and early 20th centuries, a number of non-coherent units of measure based on the gram/kilogram, centimetre/metre and second, such as the Pferdestärke (metric horsepower) for power,^[67][68] the darcy for permeability^[69] and "millimetres of mercury" for barometric and blood pressure were developed or propagated, some of which incorporated standard gravity in their definitions.^[70]

At the end of the Second World War, a number of different systems of measurement were in use throughout the world. Some of these systems were metric system variations; others were based on customary systems of measure, like the U.S customary system and Imperial system of the UK and British Empire.

The Practical system of units

In 1948, the 9th CGPM commissioned a study to assess the measurement needs of the scientific, technical, and educational communities and "to make recommendations for a single practical system of units of measurement, suitable for adoption by all countries adhering to the Metre Convention".^[71] This working document was Practical system of units of measurement. Based on this study, the 10th CGPM in 1954 defined an international system derived from six base units including units of temperature and optical radiation in addition to those for the MKS system mass, length, and time units and Giorgi's current unit. Six base units were recommended: the metre, kilogram, second, ampere, degree Kelvin, and candela.

The 9th CGPM also approved the first formal recommendation for the writing of symbols in the metric system when the basis of the rules as they are now known was laid down.^[72] These rules were subsequently extended and now cover unit symbols and names, prefix symbols and names, how quantity symbols should be written and used and how the values of quantities should be expressed.^[24]{{rp|104,130}}

Birth of the SI

In 1960, the 11th CGPM synthesised the results of the 12-year study into a set of 16 resolutions. The system was named the International System of Units, abbreviated SI from the French name, {{lang|fr|Le Système International d'Unités}}.^[24]{{rp|110}}^[73]

See also

• {{annotated link|Introduction to the metric system}}
• {{annotated link|Outline of the metric system}}
• {{annotated link|List of international common standards}}
• {{annotated link|Metre–tonne–second system of units}}

• {{annotated link|Institute for Reference Materials and Measurements}}

• {{annotated link|Conventional electrical unit}}
• {{annotated link|Coordinated Universal Time|abbreviation=UTC}}
• {{annotated link|Unified Code for Units of Measure}}

Notes

References

Further reading

• {{GreenBookRef}}
• Unit Systems in Electromagnetism
• [https://www.nist.gov/customcf/get_pdf.cfm?pub_id=32943 MW Keller et al.] Metrology Triangle Using a Watt Balance, a Calculable Capacitor, and a Single-Electron Tunneling Device
• "The Current SI Seen From the Perspective of the Proposed New SI". Barry N. Taylor. Journal of Research of the National Institute of Standards and Technology, Vol. 116, No. 6, Pgs. 797–807, Nov–Dec 2011.
• B. N. Taylor, Ambler Thompson, International System of Units (SI), National Institute of Standards and Technology 2008 edition, {{ISBN|1437915582}}.

External links

Official

• [https://www.bipm.org/en/about-us/ BIPM – About the BIPM] (home page)
  • [https://www.bipm.org/en/measurement-units/ BIPM – measurement units]
  • [https://www.bipm.org/en/publications/si-brochure/ BIPM brochure] (SI reference)
• [https://www.iso.org/iso/iso_catalogue/catalogue_ics/catalogue_detail_ics.htm?csnumber=30669 ISO 80000-1:2009 Quantities and units – Part 1: General]
• [https://physics.nist.gov/cuu/Units/bibliography.html NIST On-line official publications on the SI]
  • [https://www.nist.gov/sites/default/files/documents/2016/12/07/sp330.pdf NIST Special Publication 330, 2008 Edition: The International System of Units (SI)]
  • [https://www.nist.gov/pml/pubs/sp811/index.cfm NIST Special Publication 811, 2008 Edition: Guide for the Use of the International System of Units]
  • [https://www.nist.gov/pml/wmd/metric/upload/NIST-SP-814-Federal-Metric-Policy-1998.pdf NIST Special Pub 814: Interpretation of the SI for the United States and Federal Government Metric Conversion Policy]
• [https://www.sae.org/standardsdev/tsb/tsb003.pdf Rules for SAE Use of SI (Metric) Units]
• {{dmoz|Science/Reference/Units_of_Measurement/}}
• [https://www.engnetglobal.com/tips/convert.aspx EngNet Metric Conversion Chart] Online Categorised Metric Conversion Calculator
• [https://web.archive.org/web/20080409133218/http://lamar.colostate.edu/~hillger/pdf/Practical_Guide_to_the_SI.pdf U.S. Metric Association. 2008. A Practical Guide to the International System of Units]

History

• LaTeX SIunits package manual gives a historical background to the SI system.

Research

• The metrological triangle
• Recommendation of ICWM 1 (CI-2005)

• The music of Dan Leno
• The Music of Disney: A Legacy in Song
• The Music of Grand Theft Auto V
• The music of gta5
• The Music of GTA V
• The music of gtav
• The Music of Johnny Mathis: A Personal Collection
• The Music of Kraftwerk
• The music of Minnesota
• The Music of Nashville: Season 1 Volume 1
• The Music Of Nashville: Season 1 Volume 1
• The Music of Nashville: Season 1, Volume 1
• The Music of Nashville: Season 1, Volume 2
• The Music of Nashville: Season 1 Volume 2
• The music of nashville season 2 volume 1
• The Music of Nashville: Season 2, Volume 1
• The Music of Nashville: Season 2, Volume 2
• The Music of Nashville: Season 3, Volume 1
• The Music of Nashville: Season 3, Volume 2
• The Music of Randy Newman
• The Music of Smash
• The music of Xenosaga
• The Music or the Money…
• The Music People Ltd.
• The Music Producers Guild